Votos - 3, Puntuación media: 3.3 ( )

Fabricar: Yamaha Tamaño del archivo: 72.39 kb Nombre del archivo: Idioma del manual:

Otros manuales para este modelo:

Altavoces - NS-200 (71.95 kb)

Altavoces - NS-200 (74.69 kb)

Vibrations or jolts associated with earthquakes and other phenomena or activities may cause the speaker to fall over. For safety reasons, using commercially available products that increase stability in the speaker is recommended (metal fittings or chains, etc.). Use the stands included with the speakers to increase stability: . Stands Be sure to use the stands regardless of where the speakers are positioned. Attaching the stands included with the speakers reinforces the base of the speaker not to fall over. Please be cautioned that even though the stands are connected, this does not guarantee that the speakers will not fall over. HOW TO USE THE ACCESSORIES INCLUDED WITH THE SPEAKERS n Attaching the stand n Attaching the spike English Stand x 4 Screw (6 mm) x 4 Wood screw (4 mm) x 4 Washer x 4 Pad x 4 When positioning the speakers, be sure to use the stand to increase stability. Use the 8 specified holes located on the base of the speaker. Procedure: . Put the 6 mm screw through the inside hole on the stand. . Place a washer on the screw on the speaker side of the stand and attach to the speaker at one of the outside holes on the base of the speaker. At this time, attach the stand so that it can still be moved slightly. . Put the 4 mm wood screw through the outside hole on the stand, and screw into the inside hole on the base of the speaker. . When both screws have been attached, tighten both of the screws so that the stand is firmly in place. Be sure to check that the stand is firmly attached. A Attach the pads to the bottom of the end portion of the stand. A Attach the other stands in the same manner and confirm that all 4 stands have been firmly attached. . Place the speaker in the desired location. Note If force is applied to the side of the speaker, it may fall and damage the speaker or cause personal injury. Please be careful. Spike x 4 When setting up the speakers on a thick carpet, use the spikes instead of the stand. With 4 points set in place to achieve increased stability and improvements in sound quality. Procedure: . Set the nut close to the tip of the spike and screw them into the bottom of the speaker at each of the four specified holes. . Place the speaker in the desired location in an upright position and adjust the length of the spike to match the depth of the carpet. . When adjustment is complete, twist the nut up to the base of the speaker firmly. Notes . The tips of the spikes may scratch or otherwise damage the flooring. Please be careful when positioning the speakers. . If force is applied to the side of the speaker, it may fall and damage the speaker or cause personal injury. Please be careful. CONNECTIONS TO YOUR AMPLIFIER CONNECTIONS TO YOUR AMPLIFIER e that the amplifier is switched off. ++ – – SPEAKERS LR SPEAKERS A B LR ++ – – SPEAKERS A B LR ++ – – Speakers output terminals of the amplifier Leave the short bars in place when connecting. Short bar – Amplifier or Receiver + Loosen Tighten Speaker (L) Speaker (R) Amplifier or Receiver Amplifier or Receiver Speaker (L) Speaker (R) Speaker (L) Speaker (R) + – Remove the short bars before connecting. Woofer terminals Tweeter terminals n Connections . Connect the screw-type input terminals at the rear of the speakers to the speaker output terminals of your amplifier with the speaker cables. . Connect the (+) terminals on both the amplifier and the speakers using one side of the cable. Connect the (–) terminals on both components using the other side of the cable. . Connect one speaker to the left (marked L) terminals of your amplifier, and another speaker to the right (marked R) terminals, making sure not to reverse the polarity (+, –). If one speaker is connected with reversed polarity, the sound will be unnatural and lack bass. Procedure: . Loosen the terminal knob. . Remove approx. 10 mm (3/8”) insulation from the speaker cable and insert the bare wire end properly into the terminal hole. . Tighten the knob. . Test the security of the connection by tugging lightly on the cable at the terminal. Note Do not let the bare speaker wires touch each other as this could damage the speaker and/or the amplifier. Both SPEAKERS A and B should be selected. Bi-Wiring Connections This speaker system is capable of bi-wiring connections. To connect the speakers to the output terminals of the amplifier, two pairs of cables for each of woofer and tweeter are used instead of standard connections. This type of connection decreases the modulation distortion caused by electric resistance of the cables and driving current of the speakers. Consequently, purer sound quality can be expected. To utilize bi-wiring connections, remove the short bars from the terminals first, and then connect the woofer and tweeter to the amplifier separately using two pairs of cables. Note For bi-wiring connections, use the same type of cable for both the woofer and tweeter, making sure to match the polarity. PLACING THE S...

Descargar ahora

Introduzca dos números de la imagen: