Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
i En SUPPLIED ACCESSORIES (Only for NS-C310) SUPPLIED ACCESSORIES (Only for NS-C310) Fastener . 2 ¦To mount the speakers on a wall by using the attached mounting bracket Fasten screws into a firm wall or wall support as shown in the figure, and hang the holes of the mounting bracket on the protruding screws. * Make sure that the screws are secured in the narrow sections of the holes. Tapping screw (Available at the hardware store) PLACING THE SPEAKERS For NS-B310 ¦Using as 2ch stereo speakers Better stereo images will be obtained when the speakers are slightly angled in towards the listeners. ¦Using as front speakers and surround speakers in a surround system Position the speakers on both sides of the TV. The positioning of speakers is important, since this dictates the overall sound quality of the surround system. Set up the speakers on the basis of your listening position by following the owner’s manual supplied with your amplifier. And mount the speakers on a wall or place the speakers on a shelf. Determine the best position by following the owner’s manual supplied with your amplifier. Diameter. 3.5 to 4 mm (1/8” to 3/16”) 3 mm (1/8”) Min. 20 mm (13/16”) Wall or wall support 26 mm (1”) You can also use the screw holes on the bottom of the speaker for installing the speaker using a commercially available speaker bracket (if you do not use the attached mounting bracket). Screw holes Diameter: 6 mm (1/4”) Hole Depth: 14 mm (9/16”) 60 mm (2-3/8”) Note Placing this unit too close to a CRT TV set might impair picture color or create a buzzing noise. Should this happen, move the speaker away (more than 20 cm (7-7/8”)) from the TV set. When using a PDP or LCD TV, it would not happen. NS-B310 Front NS-C310 NS-B310 Surround Subwoofer WARNING • NS-B310 weighs 1.6 kg (3 lbs. 8 oz.). Do not mount it on thin plywood or a wall with soft surface material. If mounted, the screws may come out and the speaker may fall. This may damage the speaker, or cause personal injury. • Do not install the speaker on a wall with nails, adhesives, or any other unstable hardware. Long term use and vibrations may cause it to fall. • To avoid accidents resulting from tripping over loose speaker cables, fix them securely to the floor or wall. English 1 En Note For NS-C310 Placing this unit too close to a CRT TV set might impair picture color or create a buzzing noise. Should this happen, ¦Using as center speaker move the speaker away (more than 20 cm (7-7/8”)) from the Place the speaker on a TV rack or other stable surface. To prevent TV set. the speaker from falling down, attach the fasteners provided in When using a PDP or LCD TV, it would not happen. each corner of the speaker’s underside. WARNING Fastener ¦To mount the speakers on a wall by using the attached mounting bracket Fasten screws into a firm wall or wall support as shown in the figure, and hang the holes of the mounting bracket on the protruding screws. Make sure that the screws are secured in the narrow sections of the holes. 320 mm (12-9/16”) Diameter. 3.5 to 4 mm (1/8” to 3/16”) 3 mm (1/8”) Min. 20 mm (13/16”) Wall or wall support Tapping screw (Available at the hardware store) • NS-C310 weighs 2.9 kg (6 lbs. 6 oz.). Do not mount it on thin plywood or a wall with soft surface material. If mounted, the screws may come out and the speaker may fall. This may damage the speaker, or cause personal injury. • Do not touch the adhesive surface after peeling off the seal as this will weaken its adhesive strength. • Thoroughly wipe clean the surface where the fasteners are to be attached. Note that adhesive strength is weakened if the surface is dirty, oily or wet, and that this may cause the center speaker to drop. • Do not install the speaker on a wall with nails, adhesives, or any other unstable hardware. Long term use and vibrations may cause it to fall. • To avoid accidents resulting from tripping over loose speaker cables, fix them securely to the floor or wall. 2 En CONNECTIONS TO YOUR AMPLIFIER CONNECTIONS TO YOUR AMPLIFIER Before making connections, make sure that the amplifier is switched off. Loosen Black (–) Tighten Red (+) NS-B310 Amplifier or receiver NS-C310 NS-B310 Loosen Black (–) Tighten Red (+) ¦How to connect 1 Loosen the knob. 2 Remove 10 mm (3/8”) of insulation from each end of the cables, and twist the exposed conductors together neatly and tightly, as shown below. 10 mm (3/8 ”) Good No Good 3 Insert the bare wire. 4 Tighten the knob and secure the cables. Test the firmness of the connection by pulling lightly on the cables at the terminal. Notes • Do not let the bare speaker wires touch each other as this could damage the speaker or the amplifier, or both. • Do not insert the insulation into the hole. Sound may not be produced. ¦When using a banana plug Note Do not take off this cover unless using a banana plug. Banana plug Cover 1 Remove the cover by pulling it toward you. 2 Tighten the terminal knob. 3 Simply insert the banana plug into the terminal. • Conne...