Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
• If you play a source with Dolby, DOLBY D is displayed on the display panel for two seconds. Equalizer Change the high frequency (treble) and low frequency (bass) settings of your SoundHub. Press TREBLE +/-or BASS +/-within three seconds to change the frequency shown on the display panel. MP3 player Connect your MP3 player to play your audio files or music. What you need • An MP3 player. • A 3.5mm stereo audio cable. Play music 1 Connect the MP3 player to the SoundHub as described in the Quick star t guide. 2 Press MUSIC iLINK. » I-LINK is displayed on the display panel. 3 Press the buttons on the MP3 player to select and play audio files or music. 10 EN 7 Change settings This section helps you to change the settings of your SoundHub. Caution • The settings are already configured for optimal performance. Unless you have a reason to change a setting, we recommend that you keep the default setting. Setup menu options and settings Setup menu option Setting for the option SUBW VOL +5, +4, +3, ..., 0, ..., -3, -4, -5 DISPLAY BRIGHT DIM 1 DIM 2 SLEEP OFF, 15 MIN, 30 MIN, 45 MIN, 60 MIN VERSION RESET DEFAULT SETTINGS Setup menu options 1 Press SETUP repeatedly to cycle through the options on the display panel (see 'Setup menu options and settings' on page 11). 2 Select an option, and then press OK. 3 Press the Navigation buttons ( / ) to select a setting for the option, and then press OK. Note • If you do not press a button within ten seconds, the setup menu exits. • To exit the menu, press EXIT. • RESET DEFAULT SETTINGS is available about for ty seconds after the SoundHub is switched to on. Display panel Change the brightness of the SoundHub display panel. 1 Press SETUP repeatedly to select DISPLAY on the display panel (see 'Setup menu options and settings' on page 11). 2 Press OK. 3 Press the Navigation buttons ( / ) to select BRIGHT, DIM 1, or DIM 2, and then press OK. Sleep timer Set timers to switch the SoundHub to standby after a specified time. 1 Press SETUP repeatedly to select SLEEP on the display panel (see 'Setup menu options and settings' on page 11). 2 Press OK. 3 Press Navigation buttons ( / ) to set a sleep time on the display panel. » The sleep timer can be set up to 60 minutes. If the sleep timer is set to OFF, it switches off. Note • If you switch the SoundHub to standby, the sleep time that you have set is canceled. Apply factory settings You can reset your SoundHub to the default settings programmed at the factor y. 1 Press SETUP repeatedly to select RESET DEFAULT SETTINGS on the display panel. 2 Press OK. » TO RESET PRESS OK is displayed on the display panel. 3 Press OK again. » When the default settings are restored, RESET OK is displayed on the display panel, and the SoundHub automatically switches off and restar ts. EN 11 English 8 Product specifications Note • Specifications and design are subject to change without notice. Amplifier • Total output power : • Europe and Asia: 400W RMS (30% THD) • Latin America: 320W RMS (10% THD) • Frequency response: 20 Hz-20 kHz / ±3 dB • Signal-to-noise ratio: > 65 dB (CCIR) / (A-weighted) • Input sensitivity: • AUX1, AUX2: 450 mV • Music iLink: 170 mV Audio • S/PDIF Digital audio input: • Coaxial: IEC 60958-3 • Optical: TOSLINK Main unit • Dimensions (WxHxD): 150 x 41 x 126 mm • Weight: 0.4 kg Subwoofer • Output power : 100W RMS (30% THD) • Power supply: 220-240 V~, 50 Hz • Power consumption: 55 W • Standby power consumption: . 0.5 W • Impedance: 4 ohm • Speaker drivers: 165 mm (6.5") woofer • Frequency response: 20 Hz-150 Hz • Dimensions (WxHxD): 196 x 397 x 357 mm • Weight: 7.6 kg • Cable length: 3 m Speakers • Output power : 2 x 150W RMS (30% THD) • Speaker impedance: 6 ohm • Drivers per speaker : 2 x 64 mm (2.5") full range woofer + 1 x 64 mm (2.5") woofer + 1 x 25.4 mm (1") soft-dome tweeter • Frequency response: 150 Hz-20 kHz • Dimensions (WxHxD): 99 x 247 x 117 mm • Weight: 1.4 kg/each • Cable length: 5 m Remote control batteries • 2 x AAA-R03-1.5 V 12 EN 9 Troubleshooting Warning • Risk of electric shock. Never remove the casing of the product. To keep the warranty valid, never tr y to repair the product yourself. If you have problems using this product, check the following sections before you request ser vice. If you still have a problem, register your product and get suppor t at Sound No sound from SoundHub. • Make sure that the SoundHub is not muted. Press to select MUTE OFF on the display panel. • Connect the audio cable from your SoundHub to your TV or other devices. • Reset your SoundHub to its factor y settings, and then switch it off and switch on again. • On your remote control, press AUX, COAXIAL/OPTICAL, or MUSIC iLINK repeatedly to select the correct audio input on the display panel (see 'Listen to a connected device' on page 9). Distorted sound or echo. • If you play audio from the TV through the SoundHub, make sure that the TV is muted. Audio and video are not synchronized. • 1) Press AUDIO SYNC. 2) Within ...