Iniciar sesión:
Votos - 0, Puntuación media: 0 ( )

Manual de usuario Philips, modelo CSS2113/05

Fabricar: Philips
Tamaño del archivo: 501.87 kb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


4 Your SoundBar Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your SoundBar at Main unit a SURR indicator Lights up when surround mode is turned on. b Source indicators • COAXIAL: Lights up when you switch to coaxial input source. When Dolby signal is detected, COAXIAL indicator blinks for three seconds. • OPTICAL: Lights up when you switch to optical input source. When Dolby signal is detected, OPTICAL indicator blinks for three seconds. • AUX: Lights up when you switch to analog input source. • MUSIC iLINK: Lights up when you switch to Music iLink input source. 1 2 EN Remote control a (Standby-On) Switch the SoundBar on or to standby. b Source buttons • AUX: Switch your audio source to the AUX connection. • OPTICAL: Switch your audio source to the optical connection. • COAXIAL: Switch your audio source to the coaxial connection. • MUSIC iLINK: Switch your audio source to the MUSIC iLINK connection. c SURROUND Switch to virtual surround mode on or off. d TREBLE +/- Increase or decrease treble. e VOL +/- Increase or decrease volume. f BASS +/- Increase or decrease bass. g MUTE Mute or restore volume. Replace battery Warning • • Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. • • The product/remote control may or may not contain a coin/button type battery, which can be swallowed. Keep the battery out of reach of children at all times! Caution • • The battery contains perchlorate material, handle it with care. For information see dtsc.ca.gov/hazardouswaste/perchlorate. 1 Open the battery compartment. 2 Insert one CR2025 battery, with the polarity (+/-) as indicated. 3 Close the battery compartment. 5 1 3 4 7 6 2 3 1 2 EN 5 Connect your SoundBar This section helps you connect your SoundBar to a TV and other devices. For information about the basic connections of your SoundBar and accessories, see the quick start guide. For a comprehensive interactive guide, see Note • • For identification and supply ratings, refer to the type plate at the back or bottom of the product. • • Before you make or change any connections, make sure that all devices are disconnected from the power outlet. Subwoofer Follow the steps below to position and connect your subwoofer. Position Place the subwoofer at least one meter (three feet) away from either to the left or right of your SoundBar, and ten centimeter away from the wall. For best results, place your subwoofer as shown below. Connect Connect your subwoofer to your SoundBar as described in the quick start guide. Connectors Connect other devices to your SoundBar. Side right MUSIC iLINK Audio input from an MP3 player. Rear left a SUBWOOFER Connect to the supplied subwoofer. b AUDIO IN-AUX Connect to an analog audio output on the TV or an analog device. c DIGITAL IN-COAXIAL Connect to a coaxial audio output on the TV or a digital device. d DIGITAL IN-OPTICAL Connect to an optical audio output on the TV or a digital device. SUBWOOFER (8) L (WHITE) R (RED) AUDIO IN AUX COAXIAL OPTICAL DIGITAL IN 1 2 3 4 EN Rear right AC MAINS~ Connect to the power supply. Connect audio from TV and other devices Play audio from TV or other devices through your SoundBar. Use the best quality connection available on other devices. Note • • The audio connections in this user manual are only recommendations. You can use other connections too. • • If you play audio from the TV through your SoundBar, make sure that the TV is muted. Option 1: Connect audio through a digital optical cable Best quality audio Using an optical cable, connect the OPTICAL connector on your SoundBar to the OPTICAL OUT connector on the device. The digital optical connector might be labeled SPDIF, SPDIF OUT, or OPTICAL. Option 2: Connect audio through a digital coaxial cable Good quality audio Using a coaxial cable, connect the COAXIAL connector on your SoundBar to the COAXIAL/ DIGITAL OUT connector on the device. The digital coaxial connector might be labeled DIGITAL AUDIO OUT. Option 3: Connect audio through analog audio cables Basic quality audio Using an analog cable, connect the AUX connectors on your SoundBar to the audio connectors on the device. AC MAINS~ VCR TV EN 6 Use your SoundBar This section helps you use the SoundBar to play audio from connected devices. Before you start • Make the necessary connections described in the quick start guide and the user manual. • Switch the SoundBar to the correct source for other devices. Play audio from TV or other devices Press the Source buttons to select the audio output of the connected device. Adjust the volume To increase or decrease volume, press VOL +/-. • The Source indicators on the front panel blink thrice when the volume is set to either minimum or maximum. To mute sound, press MUTE. • The current Source indicator on the front panel blinks continuously. To restore the sound, press ...


Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría