|
Otros manuales para este modelo:
Resumen del manual
Regulates and stabilizes the volume level against a drastic volume change. ENG . REMOTE . SAT stands for Surround Air Track, which is a Samsung’s proprietary name. . The remote control can operate TVs made by SAMSUNG only. . Depending on the TV you are using, you may not be able to operate your TV with this remote control. If you can't, operate the TV using the TV's remote control. Installing Batteries in the Remote Control • Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment. • Assuming typical TV usage, the batteries last for about one year. • You can use the remote control up to 23 feet (7 meters) in a straight line from the unit. You can also operate the remote at a horizontal angle of up to 30° from the remote control sensor. Battery size: AAA 9 connections INSTALLING THE WALL MOUNT You can use the wall mount bracket to mount this unit on a wall. Installation Precautions • Install on a vertical wall only. • For the installation, avoid a location with high temperature or humidity, or a wall that cannot sustain the weight of the set. • Check the strength of the wall. If the wall is not strong enough to support the unit, reinforce the wall or install the unit on a different wall that can support the unit's weight. • Purchase and use the fixing screws or anchor appropriate for the kind of wall you have (plaster board, iron board, wood, etc.). If possible, fix the support screws into wall studs. • Connect cables from the unit to external devices before you install it on the wall. • Make sure the unit is turned off and unplugged before you install it. Otherwise, it may cause an electric shock. 1. Place the wall mount bracket on a wall surface and then secure it with two screws. If you are hanging the unit below a TV, be sure to install the wall mount bracket so that the arrow ( ) is placed in the centre of the TV. Also make sure the unit is at least two inches (5 cm) below the TV. 2. Align the two HOLDER-SCREWs (screw holders) with the screw holes on the left and right sides of the MAIN UNIT, and then fix them to the main unit with the supplied screws. 5 V0 .5A 3. Fit the unit into the corresponding slots of the wall mount bracket. For secure installation, make sure the mounting studs slide firmly down into the bottom of the slots. 4. The installation is complete. 2 inches (5 cm) or more . Do not hang onto the installed unit and avoid striking or dropping the unit. . Secure the unit firmly to the wall so that it does not fall off. If the unit falls off, it may cause an injury or damage the product. . When the unit is installed on a wall, please make sure that children do not pull any of the connecting cables, as it may cause it to fall. . For the optimal performance of a wall mount installation, install the speaker system at least 2 inches (5 cm) below the TV. . For your safety, if you do not mount the unit on the wall, install it on a secure, flat surface where it is unlikely to fall. CONNECTING THE WIRELESS SUBWOOFER ENG The Subwoofer's linking ID is preset at the factory and the main unit and subwoofer should link (connect wirelessly) automatically when the main unit and subwoofer are turned on. If the LINK indicator does not light when the main unit and subwoofer are turned on, please set the ID by following the procedure below. Complete this process within 30 seconds after the Link Indicator on the subwoofer starts blinking. 1. Plug the power cords of the main unit and subwoofer into an AC wall outlet. 2. Confirm that the main unit is off (in STANDBY Mode). . CONNECTIONS 3. Press the ID SET button on the back of the subwoofer with a small, pointed object for 5 seconds. • The LINK INDICATOR (Blue LED) on the subwoofer blinks quickly. 4. While the main unit is powered off (in STANDBY mode), press and hold the MUTE ( ) on the remote control for 5 seconds. 5. The ID SET message appears on the main unit’s OLED display. 6. To finalise the link, turn the main unit’s power on while the subwoofer’s LINK LED blinks. • The main unit and the subwoofer should now be linked (connected). • The LINK indicator (blue LED) on the subwoofer should be turned on TV S/W LEVELTV CH S/W LEVEL TONE and solid blue. • If the LINK indicator is not solid blue, the linking process has failed. Turn off the main unit and start again from Step 2. • You can enjoy better sound from the wireless subwoofer by selecting the a sound effect. (See page 24) . Before moving or installing the product, be sure to turn off the power and disconnect the power cord. . If the main unit is powered off, the wireless subwoofer will be in the standby mode and the STANDBY LED on the upper side will come on after the LINK indicator (Blue LED) blinks for 30 seconds. . If you use a device that uses the same frequency (2.4GHz) as the unit near the unit, interference may cause some sound interruption. . The transmission distance of the wireless signal between the main unit and subwoofer is about 33 ft., but may vary d...