Votos - 5, Puntuación media: 3.8
(
)
)
|
Resumen del manual
Therefore, throughout most of a movie or TV program you may not be consciously aware of output from these speakers. In other words, don’t worry if you aren’t hearing the surround speakers.Pleasetrytoavoidthetrapof turningthesurroundsup and up so that you hear them most of the time. The result will be a much less believable surround experience. There are dedicated LEFT and RIGHT model IWTS SR speakers. This is clearly marked on the back of each speaker. Be sure that the Left side surround speaker is placed directly to the left side of the prime listening area (facing the screen) and the Right speaker is directly to the right side. 6.1/7.1 Channel Systems If you are setting up a system that uses back surround speaker(s) as well as side surrounds (Dolby Digital EX, DTS ES, etc.) you can use either IWTS SR model in Dipole or Bipole mode in the back of the room. If you are using a THX Ultra 2 certified controller/receiver you should place the back surround speakers approximately 1 to 2 feet apart in the center of the back wall. The special circuitry in the processor will help to create a believable and effective surround field using this placement. Please read the electronics manual to learn more about this placement option. Speaker Placement Instruction Manual Speaker Placement Front Speaker Array should be placed as close to ear level as possible. Place the Left and Right speakers about 6-10 feet apart. Subwoofer placement is dependent on room size and shape. Left Center Right Experiment to find a location that produces the Surround Speakers smoothest response. should be placed directly to the sides of the seating area and approximately 3 feet above the listener’s Subwoofer ear level. Dipole is best setting here. Surround Back Speakers should be placed approximately 3 feet above the listener’s ear level. Either bipole or dipole setting will work well here. Speaker Installation IWTS-14 SR and 30 SR High Performance In-Wall Surround Speakers Speaker Installation NOTE: We always recommend a professional be involved in the installation of the IWTS SRs. Installation of the IWTS SRs in New Construction with Optional Bracket Removing and Installing the Grille Remove the grille from the speaker using an awl or the point of a drywall screw in a grille opening near one of the grille corners. Slowly pry the grille out, being careful not to damage the speaker’s frame or its finish. Tore-installthegrille later,press it carefully into theappropriateopeningin the frame assembly. Since it’s designed to fit snugly, please take your time For new construction,we highly recommend that you use the optional IN-NC-14/30SR New Construction Bracket. The lip on the New Construction Bracket must face outwards into the room.Sheetrockis then installed up to the lip, leaving a perfectly-defined mounting hole for the speakers. Use a level to get it straight; this can't be fixed later. Installation of the IWTS-14 SR and 30 SR in Existing Construction The IWTS SRs can be easily mounted in most any standard wall material, from . to 1. inches thick.The IWTS SR rotating wall clamps firmly fix it to the wall surface after the proper cutout has been made. An important precaution to take before mounting: Keep the top and bottom of the actual mounting hole at least 1. inches away from beams or studs to ensure that the clamps have adequate room to rotate. A crossbrace or other obstruction that’s too close will stop them from properly doing their job. and use care when installing the grille. Cutting the Opening 14 1.4” (362mm) 015-1214 10 3.4” (273mm)IWTS-14 SR and IWTS-30 SR Mounting Template After determining the best location for the speaker as outlined above, use the enclosed template to cut the proper size hole. 10. x 14.” (273 x 362mm) WARNING: Exercise extreme care before making any wall cuts to ensure that you will not cut through any wires, pipes, or other items that may be in the wall. You may sometimes, but not always, be able to determine the approximate location of wires and pipes by looking at the locations of nearby outlets and plumbing. But their location or absence is never an assurance that there is not something within the wall cavity. Speaker Wiring Instruction Manual Installing the Speaker Assembly The clamping mechanism allows the wall material to range from ." to 1." (13 to 38 mm) in thickness. There must be a minimum depth behind the wall face of 35.8” (92 mm).As noted above,be sure to keep the top and bottom of the cutout at least 1." (38mm) away from obstructions, as the rotating clamps will not operate properly if you don’t. Insert the speaker into the cutout and using a level or square carefully align it so it is level.Tighten the mounting screws, which will cause the attached clamps to rotate and position themselves properly behind the wall. Continue to tighten until the speaker is snug in the wall.You want the bezel to conform to the wallboard,and the frame not to rattle from the speaker’s vibration, but be very careful n...
Otros modelos de este manual:altavoces del coche y subwoofers - IWTS-14 SR (599.16 kb)