Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
• Forward-facing - Harness straps must be through top slots. Overhead Shield Models Only: • Harness tongue must be in opening closest to but not under child. 1 2 3 4 5 Place child in car seat with child’s back flat against back of car seat. Place harness straps over child’s shoulders and insert tongue(s) into buckle. Pull up on tongue(s) to be sure they are locked. Close harness tie: Position harness tie at arm pit level. Adjust harness straps to be snug with just enough room to insert one finger between child’s chest and harness straps (fig. a). For 5-Point models, check that harness straps on chest and thigh are snug. A rolled towel can be used on each side to support small children (fig. b). Be sure towels do not interfere with harness system. PLACING CHILD IN CAR SEAT (continued) 2 3 3 5-PointModels OverheadShieldModels 2 44 (fig. a) (fig. b) OPERATIONS and ADJUSTMENTS 1 2 3 Harness Straps (fig. a): • To tighten: Pull lower belt tab. • To loosen: Pull and hold upper belt tab while pulling harness straps. Harness Tie: • To open: Press tab and pull apart. • To close: Snap halves together. Make sure harness tie is locked by pulling out on each half. Overhead Shield Adjustment (fig. b): • To adjust shield: Push in both buttons and rotate shield to desired position closest to child. IMPORTANT: DO NOT use position three (3) with rear-facing children. NOTE: Shield does not need to contact child when in closest position; harness system restrains child. 4 Buckle: 5-Point Models • To buckle: Insert both tongues into buckle. Pull up on tongues to be sure they are locked. • To unbuckle: Press red button and pull tongues out of buckle. Overhead Shield Models • To buckle: Push tongue into opening. Pull up on tongue to be sure it is locked. • To unbuckle: Press red button and lift shield over top of car seat. 5 Recline: Recline -Rear-facing only Semi-upright - Forward-facing only Upright - Forward-facing only To adjust: Pull recline handle out and rotate car seat to desired position, then release handle (fig. c). 6 Level Adjuster (Rear-facing only): 4 Positions to adjust to vehicle seat angle: To adjust: Squeeze handle and rotate car seat to position ball in green zone, then release handle (fig. d). IMPORTANT: Level adjuster must be in position 1 when used forward-facing with car seat in semi-upright or upright positions. OPERATIONS and ADJUSTMENTS (continued) 5-PointModels 1 2 4 5 6 OverheadShieldModels 1 2 3 4 5 6 11 22 33 Upper Lower (fig. a) (fig. b) (fig. c) (fig. d) OPERATIONS and ADJUSTMENTS (continued) 7 Changing Harness Strap Slots: Rear-facing - MUST use bottom or middle harness slots which are at or below shoulders. Forward-facing - MUST use top slots. A Loosen harness straps: Pull and hold upper belt tab. Pull harness straps out. B Remove both harness strap loops from Splitter Plate on back of car seat. C Change harness strap slots. Make sure harness straps are threaded through matching slot of seat pad and car seat. It may be necessary to remove seat pad from top of car seat. D Re-attach harness strap loops to Splitter Plate: 5-Point Models (fig. e): • For Infants or Small Toddlers: Put Top right strap loop on Splitter Plate first, then attach Top left strap loop. NOTE: Make sure ends of straps are behind Splitter Plate. • For Toddlers: Put Bottom right strap loop on Splitter Plate first, then attach Bottom left strap loop. Overhead Shield Models (fig. f): Put right strap loop on Splitter Plate first, then attach left strap loop. NOTE: • Make sure both strap loops are securely attached within Splitter Plate hook. • Make sure straps are NOT twisted. OPERATIONS and ADJUSTMENTS (continued) 5-PointModels OverheadShieldModels Bottom Loop Loop Splitter Plate Top Loop (fig. e) (fig. f) VEHICLE SEAT BELTS Not all vehicle seat belts can be used with a car seat. The car seat must be held securely at all times by a lap belt (or lap belt portion of a lap/shoulder belt) that will not change length while driving. WARNING To provide the most secure installation of the car seat: • Read the vehicle owner’s manual regarding car seat installation and seat belt use with car seat. • Follow all instruction labels on vehicle seat belt and car seat. If car seat is not held securely after following instructions in this manual, vehicle seat belt labels, and vehicle owner’s manual: • Move car seat to another seating location and try again, or • Contact vehicle dealer for possible seat belt modification parts. VEHICLE SEAT BELTS (continued) 15 Vehicle seat belts located forward of seat crease may not securely hold car seat. Check vehicle owner’s manual or see vehicle dealer for car seat installation requirements. • If approved for use with car seat, install car seat and check for secure installation by pulling car seat front to back. If car seat slides forward, DO NOT use these seat belts. Seat Crease Seat Crease . Belts Forward of Seat Crease VEHICLE SEAT BELTS (continued) . Lap Belts - Manually Adjustable The locking latch plate o...