Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
SPEAKER CONNECTIONS (TRI-MODE) NON-POLAR CAPACITOR INDUCTOR (COIL) L E G E N D 100 F - + 100 F + - - 4 mH Left Mid / Tweeter 4 Ohm (2 Ohm Minimum) Mono Woofer 8 Ohm (4 Ohm Minimum) Right Mid / Tweeter 4 Ohm (2 Ohm Minimum) 12 The amplifier is capable of running in a Mono / Stereo mode. This feature gives the amplifier the ability to run stereo satellites (midbass & tweeter) simultaneously with a mono subwoofer. These connections are more complicated because they require the use of passive crossover networks (Not provided) to divide the frequencies to the speakers. We have included a sample diagram for 4 Ohm connections. If you wish to use multiple speakers to achieve a lower impedance and higher power, it is strongly recommended that you seek professional advice from your BAZOOKAd retailer before attempting to make these connections. Please Note: In the Tri-mode configuration, the amplifier’s built-in crossover must be set to the ”FLAT” position so the speakers receive full range output. BASS POWER BOOST 0dB 12dB X-OVER 60Hz 400Hz LEVEL HI INPUT INPUT REMOTE R L MIN MAX FILTER LOW FLAT HI REMOTE BASS CONTROL MODULE (OPTIONAL) Before connecting the remote, it will be necessary to find a mounting location that will be easy to access for adjustment. Once you select your mounting location, you will need to run the control wire from the remote to the amplifier. To avoid possibility of induced noise from the car's electrical system (i.e. popping noises or engine noise), run the cable from the remote to the amplifier away from the car's electrical wiring. Please note: Once the remote is plugged in, it overrides the bass boost on the amplifier and becomes the primary bass adjustment. 13 MIN MAX ADJUSTING THE X-OVER AND BAS. . (Please note: If you intend to use the amplifier in the Tri-mode configuration, it is necessary to set the crossover control to the “FLAT” setting in order to receive full range output) The “EL” amplifiers are equipped with a built-in variable crossover network allowing you to select the crossover type (i.e. Low-Pass or Hi-Pass) and the desired crossover point. For example if you wish to drive a pair of subwoofers, you can select the “Low Pass” setting on the amplifier to filter out high frequencies. This will send only low frequencies to your subwoofers (see example settings below). The crossover point should be determined by the speakers operating range. Please refer to speaker manufactures recommended crossover point. Select the crossover type on the You can add up to 12dB bass boost byamplifiers side panel. increasing the Bass Boost control. (Low-pass is selected in this example for subwoofers) Select the crossover point for your speakers. X-OVER 400Hz60Hz FILTER LOW FLAT HI BASS BOOST 12dB0dB FINE TUNE THE SYSTE. Fine tune the amplifier's input sensitivity. LEVEL The gain sensitivity control for the “EL” amplifier is located on the side panel. This gain control has been included to allow adjustment to properly match the output of the radio. This is one of the most misunderstood adjustments. By rotating the control in MIN MAX the clockwise direction, the amplifier‘s input will become more sensitive and the music will play louder. This is not a volume control and you will not get more power out of the amplifier in the maximum position! It may seem to deliver more output, but actually the system is only playing louder faster as you turn the volume control on the radio. Ideally, to properly level match the system the goal is to achieve maximum output from the amplifier without distortion at about 3/4 of the volume control. To determine if the amplifier’s gain is set properly, turn the system on and slo...
Otros modelos de este manual:Unidad - ELA150.1 (4.25 mb)
Unidad - MAA500.1 (4.25 mb)
Unidad - MAA60.4 (4.25 mb)
Unidad - ELA300.1 (4.25 mb)