Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Now insert the stereo unit into the mounting collar. Congratulations! After making a few final checks, you’re ready to enjoy your new auto stereo system. □ Final Checks Caution: Never ground the speaker cords. For example, do not use a chassis ground system or a three-wire speaker common system. Each speaker must be connected separately using parallel insulated wires. If in doubt about how your car’s speakers are wired, please consult with your nearest professional installer. Motor Antenna Connect the vehicle motor antenna lead to the blue motor antenna relay control lead. 1. Make sure that all wires are properly connected and insulated. 2. Make sure that the stereo unit is securely held in the mounting collar. 3. Turn on the ignition to check the unit for proper operation. If you have difficulties, consult your nearest authorized professional installer for assistance. 22 CQ-DP975/DFX85EUC □ Installation Procedures 1. Secure the Mounting Collar 0. Insert Mounting Collar © into the car’s dashboard, and bend mounting tabs out with a screwdriver. Mounting Tab Screwdriver 2. Secure the rear of the unit a) Check the electrical connection by referring to this operating instructions. b) Connect the Mounting Bolt @, using a suitable wrench. c) Insert the unit into Mounting Collar (D and push it in unit "click” is heard. Lock Lever Make sure that the lock lever is flush with the mounting collar (not projecting outward). ■ Using the Rear Support Strap (D Affix one end of the Rear Support Strap ® to the rear of the unit, and the other end to the Fire Wall of Car, or some other metallic area. ■ Using the Rubber Cushion (Optional) (If there is an existing Rear Support Bracket on the Fire Wall of Car.) Cover Mounting Bolt © on the rear of the unit with Rubber Cushion (Optional), and mount it into the existing Rear Support Bracket. 3) Tapping Screw Fire Wall of Car 3mm0 Rear Support Bracket (existing on the car) Installation Guide continued 3. a) Plug the Power Connector ©. b) Install the Trim plate ® . 4. After installation reconnect the negative (-) battery terminal. b) Pull out the unit while pushing two lock levers using screwdriver in the following order.(Fig.1, 2) c) Remove the unit pulling with both hands.(Fig.3) Fig. 3 24 CQ-DP975/DFX85EUC Anti-Theft System This unit is equipped with a removable face plate. By removing this face plate, the radio becomes totally inoperable. The security indicator will blink. To Remove the Removable Face Plate © Switch off the power. (2) Press the OPEN. The removable face plate will be opened. ® Push the face plate to either the right or left, then pull it out toward yourself. Security Indicator The security indicator blinks when the removable face plate is removed from the unit. Desactívate Security Indicator Press and hold SEL for more than 2 seconds when the power is ON. “LED OFF” is displayed, and the security indicator turns OFF. Display Security Indicator led ON Blinks ♦ (Press and hold SEL for more than 2 seconds.) ♦ OFF LED OFF Caution: When you want to remove the unit, the security indicator functions can be canceled by the following steps of procedure. • Install the removable face plate. • Disconnect the power connector. CQ-DP975/DFX85EUC cox I Installation Guide continued © As shown in Fig.3, gently push the lower side of the case and open its cover. Keep the removable face plate in the case. Then, you can bring the plate safety. To install the Removable Face Plate © Fit either the edge of right or left holes in the face plate over the main unit’s pin, and fit it over on the other side while pushing it. (2) After fitting the face plate holes, move the face plate up and down a few times to make sure that it has been fitted securely. (3) Close the front panel and press the right side of face plate until “click” is heard. Caution: 1. Before removing the removable face plate, make sure the power is off. 2. This removable face plate is not water-proof. Do not expose it to water or excessive moisture. 3. Do not remove the removable face plate, while driving your car. 4. Do not place the removable face plate on the dashboard or nearby areas where the temperature rises to high levels. 5. Do not touch the contacts on the removable face plate or on the main unit, since this may result in poor electrical contacts. 6. If dirt or other foreign substances get on the contacts, wipe them with a clean, dry cloth. 7. Don’t apply any strong downward force onto the face plate being open or it might be damaged. 26 CQ-DP975/DFX85EUC Electrical Connection • This unit can be connected to an optional CD changer (CX-DP801EUC). For details consult your nearest Panasonic dealers. • For connection to a CD changer, refer to the operating instructions of the CD Changer (CX-DP801 EUC). Caution: • To prevent damage to the unit, be sure to follow the connection diagram below. • Remove the covering of the leads about 5 mm lo...