Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Kenwood Tamaño del archivo: 638.22 kb Nombre del archivo: Idioma del manual:

Otros manuales para este modelo:

Unidad - DPX-MP4030 (1.02 mb)

Unidad - DPX-MP4030 (994.5 kb)

Unidad - DPX-MP4030 (3.71 mb)

To car light control switch Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. Power control wire (Blue/White) Motor antenna control wire (Blue) Dimmer control wire (Orange/White) Front left output (White) Front right output (Red) Rear left output (White)/ Non-fading left output (White) Rear right output (Red)/ Non-fading right output (Red) — 30 — 30— 30 — —— Installation Installation When performing a place this unit in a horizontal of the CD. ¦ Installation Install onto the car bracket using . 6 mm, M5 . 7 mm). The holes of the car bracket depending on the car model. When a ground wire is included in the wiring kit (which is sold separately), fasten the ground wire with the binding screw located on the rear panel of this unit. Accessory1 (M5 . 6 mm) or Accessory4 (M5 . 7 mm) Accessory3 Screw (M4X8) (commercially available) (Only for NISSAN car) — 31 — 31— 31 — —— English English What might seem just be the result Before calling service, for possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? There’s a source you can’t switch. . There’s no tape inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't switch to each source. . There’s no CD inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't switch to each source. . The Disc changer isn’t connected. . Connect the Disc changer. If the Disc changer isn’t connected to it's input terminal, You can't switch to an external disc source. ? The memory is erased when the ignition is turned OFF. . The battery wire has not been connected to the proper terminal. . Connect the wire correctly, referring to the section on (page 30). . The ignition and battery wire are incorrectly connected. . Connect the wire correctly, referring to the section on (page 30). ? No sound can be heard, or the volume is low. . The fader or balance settings are set all the way to one side. . Center the fader and balance settings. . The input/output wires or wiring harness are connected incorrectly. . Reconnect the input/output wires or the wiring harness correctly. See the section on (page 30). . The cassette tape . Try playing another cassette bad. ? The sound quality is poor . One of the speaker wires is being . Check the speaker wiring. . The tape head is dirty. . Clean the tape head. . The speakers are not wired correctly. . Reconnect the speaker wires so that each output connected to a different speaker. ? Non-fading setting can’t be done. . The (page 24) is set on Rear preout. . Set it on Non-fading preout. ? The text is not scrolled. . This is because eight or less characters are displayed. . If all the characters are displayable on the display part, the text is scrolled once when the display switches, and after that, the text is not scrolled. ? The Security Code item isn’t displayed in the Function System. . The Security Code function is already activated. . When the Security Code function is activated it isn’t displayed in the Function items. ? The Touch Sensor Tone doesn’t sound. . The preout jack is being used. . The Touch Sensor Tone can’t be output from the preout jack. ? Even though the vehicle light switch is turned ON, the unit’s display won’t dim. . The dimmer wire isn’t connected. . Connect the dimmer wire correctly. ? The display color changes subtly. . This is because the temperature is different than the temperature when the setting was done. . The display color condition changes subtly according to the ambient temperature. — 32 — Tuner source Tuner source ? Radio reception is poor. ? "AUX" is displayed without . The car antenna is not extended. . O-N switch is set to "O" side. . Pull the antenna out all the . Set the switch to "N" side. . The antenna control wire is not . Connect the wire correctly, referring to the section on (page 30). ? The desired frequency can’t be entered with the Direct Access Tuning. . A station that can’t be received is being entered. . Enter a station that can be received. . You’re trying to enter a frequency with a 0.01 MHz unit. . What can be designated in the FM band is to 0.1 MHz. Cassette tape source ? Can’t remove tape. . The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF. . The tape can only be removed within 10 minutes of the ACC switch being turned OFF. If more than 10 minutes has elapsed, turn the ACC...

Descargar ahora

Introduzca dos números de la imagen: