Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Starting the Track Scan: — 15 — English External Magazine Random ( Function of disc Play the tracks on order. 1 Press the M.RDM button and off. The RDM indicator lights up when turned on. The disc and track numbers will change display as the next track is being selected. When the disc/track has been selected, The selected disc/track number blinks in the being played. 2 To change the track being heard, press the . button. Another disc/track will be selected and played. NOTE • Magazine random play is canceled when you eject the disc. • The time needed for random selection depends on the number of discs loaded in the disc magazine. — 16 — Accessories Installation Installation External view Number of .......................................... 1 .......................................... 1 .......................................... 2 1. To prevent disconnect the - battery. 2. Make the proper 3. Connect the speaker 4. Connect the wiring harness battery, ignition. 5. Connect the wiring harness 6. Install the unit in your car. 7. Reconnect the - battery. 8. Press the reset button. .......................................... 1 .......................................... 4 6 .......................................... 4 .......................................... 1 7 2CAUTION The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 2CAUTION • If your car's ignition does not have an ACC position, the ignition wires to a power source that can be off with the ignition key. If you connect the ignition power source with a constant voltage supply, as with wires, the battery may die. • If the console has a lid, make sure to install the unit so that faceplate will not hit the lid when closing and opening. • If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating. • Do not let unconnected wires or terminals touch metal on the car or anything else conducting electricity. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Insulate unconnected wires with vinyl tape or other similar material. • Some disc changers need conversion cords for connection. See the section on "Safety Precautions" for details. — 17 — Connecting Rear left output Front left output English Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. Car fuse box (Main fuse) Battery 2WARNING KENWOOD disc P.CONT ANT. CONT. FRONT • L FRONT • R – + Rear right output (Red) Fuse (10A) Wiring harness (Accessory1) Power control/Motor antenna control wire (Blue/White) Ignition wire (Red) Battery wire (Yellow) Ignition key switch ACC Car fuse box If no connections are made, do not let the wire come To connect the Disc changer, consult your Disc changer NOTE Ground wire (Black) · (To car chassis) 2CAUTION (KRC-409 only) FM/AM antenna input Front right output (Red) (KRC-409 only) White/Black White To front left speaker Gray/Black Gray To front right speaker REAR • L Green/Black Green To rear left speaker Purple/Black REAR • R Purple To rear right speaker When only two speakers are being connected to the system, connect the connectors either to both the front If you connect the ignition wire (red) and the battery wire output terminals or to both the rear output terminals (do not (yellow) to the car chassis (ground), you may cause a short mix front and rear). For example, if you connect the + circuit, that in turn may start a fire. Always connect those connector of the left speaker to a front output terminal, do wires to the power source running through the fuse box. not connect the - connector to a rear output terminal. — 18 — Installation Installation Installing Accessory4 Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and Firewall or metal support 1 Refer to the section “ Removing the hard ” and then remove the 2 Align the holes in the unit the vehicle mounting bracket accessory screws. T: Toyota cars N: Nissan cars Accessory5...for Nissan car Accessory6 ...for Toyota car 8 mm MAX. o5mm o5mm 8mm MAX. T N N T T/N 5 6 Self-tapping Accessory2 attach it in place. 2CAUTION screw Metal mounting • During installation, do not use any screws except for those (commercially strap provided. The use of different screws might result in damage available) to the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. NOTE Make sure that the unit is installed securely in p...
Otros modelos de este manual:Unidad - KRC-309S (328.06 kb)