Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
button Bass ("Bass") Bass decreased. Bass increased. Middle("Middle") Middle decreased. Middle increased. Treble("Treble") Treble decreased. Treble increased. Balance("Balance") Left channel emphasized. Right channel emphasized. Fader("Fader") Rear channel increased. Front channel increased. Volume Offset ("V Offset") The sound level of each source decreased. The sound level of each source increased. 4 Press the AUD button to end the control mode. NOTE Determining the parameters in the audio control setting would clear all the adjustments made in the System Q and they are replaced with the values in the audio control setting. Faceplate Angle Adjustment You can adjust the faceplate angle for easy viewing. Sliding the faceplate: Press the ANG button for at least one second. — 8— NOTE • Do not apply excessive • The face plate angle Forced Closing This function prevents tampering with being serviced etc. Hiding the unit with the ignition turned on Press the SRC button for at least one second. The faceplate will slide open. When the period of you have set in the "Time setting for removing the faceplate" the menu has passed, the faceplate automatically reverses hide the control panel. However, you can remove the faceplate during that period. For details, refer to the "Removing the faceplate" (page 10). NOTE • When the closing faceplate is hit by an object, the unit will turn off without the faceplate closing all the way. Remove the object and press the SRC button to turn the unit back on, then turn it off again to have it close properly. • Do not try to press the buttons on the control panel as the faceplate is moving, as excessive force may damage the unit. • During the forced closing of the unit (i.e., having the unit left closed while ignition is turned on), the faceplate will not open no matter how often the ignition is turned on or off. You can prevent tampering of the unit when letting someone else drive your car by keeping it closed this way. To cancel the forced closing of unit and open control panel: Press the left part at the upper side of the faceplate. The faceplate will open and show the control panel. — 9— General English Removing the The faceplate can theft. Removing the faceplate: 1 Choose the way from among faceplate. Turn the ignition off, press the SRC second when the control panel has 2 Holding the center part of the faceplate, period which you have set in the "Time setting the faceplate" (page 26) in the menu. The faceplate bracket will automatically close. 1 Hold the faceplate toward you and set faceplate bracket. 2CAUTION Do not set the right side of first, when reattaching the faceplate. connector on the faceplate bracket 2 Press the right side of the faceplate 2CAUTION Clock display • When removing the faceplate, pull it out only when it is fully open. The detachment of the faceplate while it is moving might result in damage to the unit. • Do not apply excessive force to the faceplate bracket without attaching the faceplate. Doing so will cause the faceplate bracket to be deformed. • Do not touch the connector on the faceplate bracket after removing the faceplate. Touching the connector may cause damage to the unit. Changing the Clock Display: Each time you press the CLK button, the display switches between the clock and each mode display. NOTE The clock indicator lights while the clock is displayed. NOTE • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case while detached. • Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Reattaching the Faceplate: — 10 — Tuner features AUTO /AME 38 SRC FM ANG PROG AME AUD SCANB NR B.S/RDM REP MTL/M.RDMLOUD DISP NAME.S PWR OFF AUTO # 1-6 DISP 4 AM . /NAME.s Frequency AUTO indicator ST indicatorBand display Preset station number — 11 — Tuner features English Tuning You can choose from station seek, and manual. when auto seek tuning lights when preset station Selecting Tuning Mode: Press the AUTO button. Each time you press the AUTO button, follows. Ў Auto 1 (Auto Seek Tuning) Ў Auto 2 (Preset Station Seek Tuning) Ў Manual (Manual Tuning) Tuning: 1 Press the SRC (source) button repeatedly to select the tuner mode. "TUNER" is displayed when the tuner mode has been selected. 2 Press either the FM or AM button to select the band. Each time you press the FM button, the band switches between the FM1, FM2 and FM3 (which are used for groups of preset stations) . Press the AM button to select the AM band. 3 • Auto Seek Tuning Press the . button to seek higher frequencies. Press the 4 button to seek lower frequencies. • Preset station seek tuning Press the . button to move to the next preset station (i.e., the one with the next highest number), and the 4 button to move to the last preset station (i.e., the one with the next lowest number). • Ma...