Votos - 3, Puntuación media: 5 ( )

Fabricar: Kenwood Tamaño del archivo: 443.79 kb Nombre del archivo: Idioma del manual:

• Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. • When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Mount the unit so that the mounting angle is 30° or less. — 17 — English English P.CONT.OUT ANT. CONT. FRONT • L FRONT • R REAR • L REAR • R – + REARLRFM/AM antenna input Rear left output (White) Rear right output (Red) Fuse (10A) KENWOOD disc changer control Wiring harness (Accessory1) White/Black Gray/Black Green/Black Purple/Black White Gray Green Purple To front left speaker To front right speaker To rear right speaker To rear left speaker Ignition wire (Red) Battery wire (Yellow) Ground wire (Black) · (To car chassis) Ignition key switch Car fuse box (Main fuse) ACC Car fuse box Battery If no connections are made, do not let the 4 Front left output Front right output (Red) To connect the Disc changer, consult your Disc changer manual. Power control/Motor antenna control wire (Blue/White) Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. — 18 — Installation Installation Installation Firewall or metal support Self-tapping screw (commercially available) Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Metal mounting strap (commercially available) Screw (M4X8) (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. ¦ Installing in 1 Refer to the section and then remove the hard 2 Align the holes in the unit vehicle mounting bracket and screws. T: Toyota cars N: Nissan cars Accessory3...for Nissan car Accessory4 ...for Toyota car • During installation, do not use any screws except for those provided. The use of different screws might result in damage to the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. ¦ Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off, screw in the provided screw (o4 X 16 mm) in the hole shown below. Accessory5 8 mm MAX. o5mm o5mm 8mm MAX. T N N T T/N 3 4 Never insert the taptite screw (o4 . 16 mm) in any other screw hole than the one specified. If you screw it in another hole, it will contact and may cause damage to the mechanical parts inside the unit. — 19 — English English ¦ Removing the ¦ Removing the 1 Refer to the section 1 Engage the catch pins remove the hard rubber locks on the lower level. Lower the frame and pull 2 Remove the screw (M4 . 8) on the back panel. 2 When the lower level is removed, remove the upper two locations. Catch Lock Accessory2 Removal tool Accessory2 Removal toolScrew (M4X8) (commercially available) 3 Insert the two removal tools as shown. 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. The frame can be removed from the top side in the same manner. — 20 — Troubleshooting Troubleshooting General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the res...

Descargar ahora

Introduzca dos números de la imagen: