Votos - 3, Puntuación media: 4.3 ( )

Fabricar: Kenwood Tamaño del archivo: 501.94 kb Nombre del archivo: Idioma del manual:

The use of different screws might result in damage to the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. ¦ Screwing the Faceplate on the Unit (KDC-3026/KDC-2026/KDC-226/KDC-226B only) If you want to fasten the faceplate to the main unit so that it does not fall off, screw in the provided screw (o4 X 16 mm) in the hole shown below. Accessory5 Never insert the taptite screw (o4 . 16 mm) in any other screw hole than the one specified. If you screw it in another hole, it will contact and may cause damage to the mechanical parts inside the unit. — 15 — 15— 15 — —— Installation Installation ¦ Removing the 1 Engage the catch pins locks on the lower level. Lower the frame and pull Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper two locations. The frame can be removed from the top side in the same manner. ¦ Removing the 1 Refer to the section remove the hard rubber 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools as shown. Screw (M4X8) (commercially available) Accessory2 Removal tool 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. — 16 — 16— 16 — —— Troubleshooting Troubleshooting General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? The sound quality . One of the speaker . Check the speaker wiring. . The speakers are not wired . Reconnect the speaker wires connected to a different speaker. ? The Touch Sensor Tone doesn’t sound. . The preout jack is being used. . The Touch Sensor Tone can’t be output from the preout jack. Tuner source ? Radio reception is poor. . The car antenna is not extended. . Pull the antenna out all the way. . The antenna control wire is not connected. . Connect the wire correctly, referring to the section on ? There’s a source you can’t switch. (page 14). . There’s no CD inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't swhich to each source. ? The memory is erased when the ignition is turned OFF. . The battery wire has not been connected to the proper terminal. . Connect the wire correctly, referring to the section on (page 14) . . The ignition and battery wire are incorrectly connected. . Connect the wire correctly, referring to the section on (page 14) . ? Even if Loudness is turned ON, high-pitched tone isn't compensated for. . Tuner source is selected. . High-pitched tone isn't compensated for when in Tuner source. ? No sound can be heard, or the volume is low. . The fader or balance settings are set all the way to one side. . Center the fader and balance settings. . The input/output wires or wiring harness are connected incorrectly. . Reconnect the input/output wires or the wiring harness correctly. See the section on (page 14). — 17 — English English Disc source ? "AVin" is displayed without . Unsupported disc changer . Use the disc changer mentioned INFORMATION of the section on (page 5). ? Can’t remove disc. . The cause is that more ACC switch was turned . The disc can only be removed switch being turned OFF. If more than 10 m...

Descargar ahora

Introduzca dos números de la imagen: