Votos - 3, Puntuación media: 4.7 ( )

Fabricar: Kenwood Tamaño del archivo: 545.83 kb Nombre del archivo: Idioma del manual:

Otros manuales para este modelo:

Unidad - KDC-4024V (570.94 kb)

Unidad - KDC-4024V (1.56 mb)

To link the unit's power to the ignition, connect the ignition cable (ACC...red) to a power source that can be turned on and off with the Installation ¦ Installation Firewall or metal support Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Metal mounting strap (commercially available) Self-tapping screw (commercially available) Screw (M4X8) (commercially available) ignition key. — 24 — ¦ ¦ 1 Engage the catch pins locks on the lower level. Lower the frame and pull Catch Lock Accessory2 Removal tool 2 When the lower level is removed, remove the upper locations. The frame can be removed from the top side in the same manner. ¦ Removing the 1 Refer to the section remove the hard rubber 2 Remove the screw (M4.8) on the back panel. 3 Insert the two removal tools deeply as shown. Screw (M4X8) (commercially available) Accessory2 Removal tool 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. — 25 — English English What might seem just be the result Before calling service, for possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, one with the same rating. . No ACC position on vehicle ignition. . Connect the same wire to the ignition as the battery ? Nothing happens when the buttons are pressed. . The computer chip in the unit is not functioning normally. . Press the reset button on the unit (page 4). ? There’s a source you can’t switch. . There’s no CD inserted. . Set the media you want to listen to. If there’s no media in this unit, you can't swhich to each source. ? The memory is erased when the ignition is turned OFF. . The battery wire has not been connected to the proper terminal. . Connect the wire correctly, referring to the section on . . The ignition and battery wire are incorrectly connected. . Connect the wire correctly, referring to the section on . ? The TEL mute function does not work. . The TEL mute wire is not connected properly. . Connect the wire correctly, referring to the section on . ? The TEL mute function turns ON even though the TEL mute wire is not connected. . The TEL mute wire is touching a metal part of the car. . Pull the TEL mute wire away from the metal part of the car. ? Even if Loudness for. . Tuner source is selected. . High-pitched tone isn't compensated source. ? No sound can be heard, or the . The fader or balance settings are . Center the fader and balance settings. . The input/output wires or wiring harness . Reconnect the input/output wires or the wiring See the section on . ? The sound quality is poor or distorted. . One of the speaker wires is being pinched by a screw . Check the speaker wiring. . The speakers are not wired correctly. . Reconnect the speaker wires so that each output terminal is connected to a different speaker. ? The Touch Sensor Tone doesn’t sound. . The preout jack is being used. . The Touch Sensor Tone can’t be output from the preout jack. ? Even though Synchronize Clock is ON, the clock can’t be adjusted. . The received RDS station isn’t sending time data. . Receive another RDS station. Tuner source ? Radio reception is poor. . The car antenna is not extended. . Pull the antenna out all the way. . The antenna control wire is not connected. . Connect the wire correctly, referring to the section on . ? It isn't the set Traffic information sound volume. . The set sound volume is less than the tuner sound volume. . If the tuner sound volume is louder than the set sound volume,the tuner sound volume is used. — 26 — Disc source Disc source . Unsupported disc changer . Use the disc changer mentioned INFORMATION of the section on Otros modelos de este manual:
Unidad - KDC-3024 (545.83 kb)
Unidad - KDC-307 (545.83 kb)
Unidad - KDC-4024 (545.83 kb)

Descargar ahora

Introduzca dos números de la imagen: