Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
2CAUTION • Be sure not to place the unit exposed to direct sunlight It results in the deformation • Depending on the installing be able to receive them after confirming • Install the unit — 17 — Troubleshooting guide Troubleshooting guide calling service, first check the following table for possible problems. PROBLEM POSSIBLE CAUSE SOLUTION English Turn the power button ON. Connect the input/output wire or wiring harness correctly. See "Connecting Wires to Terminals" (Page 15). Press the Reset button of the display unit. Connect the CD auto-changer input to the unit. Eject the disc magazine and check the specified disc. Check and, if possible, clean the disc. See "Cleaning CDs" (Page 6). Eject the disc magazine and insert the disc correctly. Eject the disc magazine and insert the discs Use another disc. Check wires for shorts, then replace the fuse with one of with the same rating (shown on the case). Adjust the fader and balance. Raise the volume level. Use the appropriate volume level. Set the O-N selection switch to "O" position. The power is not turned on. No sound or sound is low. The unit does not work properly when a button is pressed. Sound quality is poor. (Sound distortion) CD play does not start. The specified disc is not played; a different disc is played instead. The wiring harness fuse blows. The O-N selection switch of the disc changer is not set properly. The volume level is minimum. The fader or balance is set to one side. The input/output wire or wiring harness is connected incorrectly. The microcomputer malfunctions. The volume level is too high. CD auto-changer input is not connected to the unit. Power button is not turned ON. The specified disc is very dirty. The disc is loaded upside down. Two discs are inserted in a slot. The number of the slot into which the different from the number of the The disc is severely damaged. — 18 — Troubleshooting guide Troubleshooting guide Sound skips due to vibration. Something is touching the CD auto-changer. Keep it away from the CD auto-changer. The disc is dirty or damaged. If sound skips at the same part, the disc is faulty. Check and, if possible, clean the disc. See "Cleaning CDs" (Page 6). The unit is mounted at a slant. Mount the unit so that is level. Changer unit is mounted in an unstable place. Mount the unit in a stable place. The angle adjustment switches are set improperly. Set the angle adjustment switches to the correct positions. Nothing appears on the display. The control output of the display unit is not connected properly. Connect the control output properly. Sound distortion. A disc with a high recording level is used. Change the modulation level / dynamic control setting.(Page 13) Sound quality is poor. The recording of the disc is poor. Try playing another disc. If the sound is good, the fault was with the original disc. The disc is dirty or damaged. Check and, if possible, clean the disc. See "Cleaning CDs" . (Page 6)" No sound is heard even though the information concerning the CD auto-changer is displayed. Volume is set to minimum level. Raise the volume level. The microcomputer does not function correctly. Press the Reset button of the display unit. The system is not connected properly. Connect the system properly. See "Connecting Wires to Terminals" .(Page 15) The specified track is not played. The player is set to Random Play / Magazine Random Play. Turn off Random Play / Magazine Random Play. — 19 — English English The following messages are displayed when certain problems are occurring in your system. Take actions. 01 E: No disc magazine has been loaded in the changer. The disc magazine is not completely loaded. ] Load the disc magazine properly. 02 E: No disc has been loaded in the disc magazine. ] Load a disc into the disc magazine. 04 E: No disc has been loaded in the disc magazine. ] Load a disc into the disc magazine The CD is quite dirty. The CD is upside-down. The CD is scratched a lot. ] Clean the CD and load it correctly. 77 E: The unit is malfunctioning for some reason. ] Press the reset button on the unit. If the "77E" code does not disappear, consult 99 E: Something is wrong with the disc magazine. Or the unit is malfunctioning ] Check the disc magazine. And then, press the reset button on the If the "99E" code does not disappear, consult your nearest service 0d E: The protective circuit in the unit activates when the temperature all operation. ] Cool down the unit by opening the windows or turning will start playing again. — 20 — Specifications Specifications Disc section Laser Diode.....................................................GaAlAs ( .=780 nm) Digital Filter (D/A) ......................................8 Times Over Sampling D/A Converter.........................................................................1 bit Spindle speed ...............................................500 ~ 200 rpm (CLV) Wow & Flutter.........................................Below Measurable Limit Frequency Response (±1 dB) ......
Otros modelos de este manual:Unidad - KDC-C467FM (476.99 kb)