Votos - 4, Puntuación media: 4.3 ( )

Fabricar: Kenwood Tamaño del archivo: 1.09 mb Nombre del archivo: Idioma del manual:

To KENWOOD disc changer/ External optional accessory When using the optional power amplifier, connect to its power control terminal. Power control wire (Blue/White) Motor antenna control wire (Blue) Depending on what antenna you are using, connect either to the control terminal of the motor antenna, or to the power terminal for the booster amplifier of the film-type antenna. To front left speaker To front right speaker To rear left speaker To rear right speaker White/Black White Gray/Black Gray Green/Black Green Purple/Black Purple Ignition key switch Car fuse box (Main fuse) Connect to the terminal that is grounded TEL mute wire (Brown) when either the telephone rings or during conversation. Front left output (White) Front right output (Red) Video output (Yellow) To the monitor unit Parking sensor wire (Green) To connect these leads, refer to the relevant instruction manuals. To parking brake detection switch harness of car For the sake of safety, be sure to connect the parking sensor. Connection cable (Accessory9) English | 25 • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). non-Japanese cars Japanese cars 1 Refer to the section (page 27) and then remove the hard rubber frame. 2 Align the holes in the unit (two locations on each side) with the vehicle mounting bracket and secure the unit with the accessory screws. • During installation, do not use any screws except for those provided. The use of different screws might result in damage to the main unit. • Damage may occur if a screwdriver or similar tool is used with excessive force during the installations. Installation Firewall or metal support Screw (M4X8) (commercially available) Self-tapping screw (commercially available) Metal mounting strap (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. 8 mm MAX. o5mm o5mm 8mm MAX. T N T N T/N T: Toyota cars N: Nissan cars Accessory3...for Nissan car Accessory4 ...for Toyota car 3 4 Using the Relay Connector 1 Plug the vehicle’s harness into the relay connector. 2 Plug the parking brake detection wire into the relay connector. Detection wire Relay connector Accessory0 Vehicle harness 2 1 3 Lock the cable clamp. Cable clamp 3 4 Press down using pliers until the conductive metal is even with the plastic surface. 5 Lock the lid. Lid 4 5 Conductive metal 26 | English Installation Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off. 1 Refer to the section (page 27) and then remove the hard rubber frame. 2 Drop open the faceplate by pressing the Release button. 3 Tighten the stepped screw (Accessory 5) in the hole shown on the diagram. Accessory5 4 Tighten the screw (o2 . 5 mm) (Accessory 6) and bracket (Accessory 7) in the hole shown on the diagram. Accessory6 Accessory7 5 Tighten the screw (o2 . 5 mm) (Accessory 6) and bracket (Accessory 8) in the hole shown on the diagram. Accessory6 Accessory8 • Never insert the screws in any other screw hole than the one specified. If you screw them in another hole, it will contact and may cause damage to the mechanical parts inside the unit. Accessory5 ..........1 Accessory6 ..........2 English | 27 Removing the Unit Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. 2 When the upper level is removed, remove the lower two locations. • The frame can be removed from the bottom side in the same manner. Removing the Unit 1 Refer to the section (page 27) and then remove the hard rubber frame. 2 Remove the screw (M4 . 8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, as shown. 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. • Be careful to avoid injury from the catch pins on the removal tool. 5 Pull the unit all the way out with your hands, being careful not to drop it. Catch Lock Accessory2 Removal tool Accessory2 Removal tool Screw (M4X8) (commercially available) 28 | English Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. . The fuse has blown. . After checking for short circuits in the wires, replace the fuse with one with the same rating. . The speaker wire has a short-circuit or touches the chassis of the vehicle, and then the protection function is activated. . Wire or insulate the speaker cable properly and press the reset button. ? There’s a source you can’t switch. . There’s no media inserted. . Set the media you want to listen to. If t...

Descargar ahora

Introduzca dos números de la imagen: