Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
6. Connect the wiring harness connector to the unit. 7. Install the unit in your car. 8. Reconnect the - terminal of the battery. 9. Press the reset button. ¤ • Mounting and wiring this product requires skills and experience. For safety’s sake, leave the mounting and wiring work to professionals. • Make sure to ground the unit to a negative 12V DC power supply. • Do not install the unit in a spot exposed to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. • Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit. • If the power is not turned ON (“PROTECT” is displayed), the speaker wire may have a short-circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked. • Make sure that all wire connections are securely made by inserting jacks until they lock completely. • If your vehicle’s ignition does not have an ACC position, or if the ignition wire is connected to a power source with constant voltage such as a battery wire, the power will not be linked with the ignition (i.e., it will not turn on and off along with the ignition). If you want to link the unit’s power with the ignition, connect the ignition wire to a power source that can be turned on and off with the ignition key. • Use a commercially available conversion connector if the connector does not fit in the vehicle connector. • Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. • If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. • If the fuse blows, first make sure the wires aren’t touching to cause a short circuit, then replace the old fuse with one with the same rating. • Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Mount the unit so that the mounting angle is 30° or less. About CD players/disc changers connected to this unit Kenwood disc changers/ CD players released in 1998 or later can be connected to this unit. Refer to the catalog or consult your Kenwood dealer for connectable models of disc changers/ CD players. Note that any Kenwood disc changers/ CD players released in 1997 or earlier and disc changers made by other makers cannot be connected to this unit. Connecting unsupported disc changers/CD players to this unit may result in damage. Set the “O-N” Switch to the “N” position for the applicable Kenwood disc changers/ CD players. The functions you can use and the information that can be displayed may differ depending on the models being connected. 18 | KDC-W5641U/KDC-W5541U/KDC-W5141U/KDC-W5041U/KDC-W4141/KDC-W4041 Connecting Wires to Terminals P.CONT ANT.CONT 1234567812345678MUTE KDC-W5641U/W5541U/W5141U/W5041U KDC-W4141/W4041L R L R Rear preout/SubWoofer preout Rear/SubWoofer preout REMO.CONT Battery wire (Yellow) Ignition wire (Red) FM/AM antenna input (JASO) (KDC-W5641U/W5541U/W5141U/W5041U) .To connect the Kenwood navigation system, consult your navigation manual. Wiring harness (Accessory1) If no connections are made, do not let the wire come out from the tab. Power control/ Motor antenna control wire (Blue/White) TEL mute wire (Brown) Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. Connect to the terminal that is grounded when either the telephone rings or during conversation. A–7 Pin (Red) A–4 Pin (Yellow) Connector A Connector B Fuse (10A) . See next page. FM/AM antenna input (JASO) (KDC-W4141/W4041) Steering remote control (Light Blue/Yellow) To Kenwood disc changer/ External optional accessory To use the steering wheel remote control feature, you need to an exclusive remote adapter (not supplied) matches your car is required. When this terminal is not in use, leave its cap on. English | 19 Connecting Wires to Terminals Connector Function Guide 2WARNING Pin Numbers for ISO Connectors External Power Connector A-4 A-5 A-6 A-7 A-8 Speaker Connector B-1 B-2 B-3 B-4 B-5 B-6 B-7 B-8 Cable Colour Yellow Blue/White Orange/White Red Black Purple Purple/Black Gray Gray/Black White White/Black Green Green/Black Functions Battery Power Control Dimmer* Ignition (ACC) Earth (Ground) Connection Rear Right (+) Rear Right (–) Front Right (+) Front Right (–) Front Left (+) Front Left (–) Rear Left (+) Rear Left (–) *Function of KDC-W5641U/W5541U/W5141U/W5041U. Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make th...
Otros modelos de este manual:Unidad - KDC-W4041 (393.47 kb)
Unidad - KDC-W4141 (393.47 kb)
Unidad - KDC-W5041U (393.47 kb)
Unidad - KDC-W5541U (393.47 kb)