Votos - 2, Puntuación media: 4.5
(
)
)
|
Otros manuales para este modelo:
Resumen del manual
In the case of frequent acceleration, set it up to "G-Counter: Level3". Function of the KDC-W7031 In Standby mode G-Analyzer Reset Resets the value of G-Meter and G-Counter. 1 Select G-Analyzer Reset mode Push the Control knob to [FM] or [AM]. Select the "G-Reset" display. 2 Enter G-Analyzer Reset mode Press the Control knob for at least 1 second. 3 Select the Reset item Push the Control knob to [FM] or [AM]. "G-Meter Reset": Reset the value of G-Meter. "G-Counter Reset": Reset the value of G-Counter. 4 Reset the value Press the Control knob for at least 2 seconds. "Reset OK" is displayed. 5 Exit G-Analyzer Reset mode Press the [MENU] button. Function of the KDC-W7031 In Standby mode G-Analyzer Calibration setup G-Analyzer requires calibration for horizontal acceleration and braking. • Detection of horizontal and straight directions should be done at horizontal location to go straight. 1 Park the vehicle at horizontal location 2 Select G-Analyzer Calibration set mode Push the Control knob to [FM] or [AM]. Select the "G-Calibration" display. 3 Enter G-Analyzer Calibration set mode Press the Control knob for at least 1 second. "Stop" is displayed. 4 Start Calibration of horizontal direction Press the Control knob. Once "Move Forward" appears on the display, the vehicle must be advanced. 5 Start Calibration of straight direction When the vehicle is driven on the straight direction, calibration of straight direction automatically starts. • In order to operate the detection of straight direction. When the Calibration is finished, "Calibration OK" is displayed. • If you fail to complete the calibraton, "No Calibration" is displayed. In such a case, repeats step 1 thru 6. 6 Exit G-Analyzer Calibration set mode Press the [MENU] button. 38 | English Menu system Function of the KDC-W7031 G-Analyzer Stop Watch The control of stop watch can be started by GAnalyzer function. • Do not use G-Analyzer stop watch on the Public roads. 1 Select G-Analyzer Stop Watch mode Push the Control knob to [FM] or [AM]. Select the "Stop Watch" display. 2 Enter G-Analyzer Stop Watch mode Press the Control knob for at least 1 second. "Stop" is displayed. 3 Enter Counter Ready mode Press the Control knob. "Ready" is displayed. 4 Start Count When G on the vertical direction is detected during the traveling, the count is automatically started. "Running" is displayed. • You can also start the counter by pressing the Control knob. 5 Stop Count Press the Control knob. "Stop" is displayed. • The control will be started again when you accelerate or press the Control knob. Do the operation after step3. When you Reset the Count (While "Stop" is displayed) Press the Control knob for at least 2 seconds. • The reset of count can be done when the count is stopped. 6 Exit G-Analyzer Stop Watch mode Press the [MENU] button. • When "Running" is displayed (counted), the count is continued on although G-Analyzer Stop Watch mode is finished. If you want to stop the count, enter the menu mode then press the control knob. • When Power off (ex; ACC OFF) while counting, the value of 1 second or less will be "00". Other than Standby mode/ When the Dual Zone System is ON Dual Zone System Setting Setting the Front channel and Rear channel sound in the Dual Zone System. Display Setting "Zone 2 : Rear" Sub source (Auxiliary input source) is to be rear channel. "Zone 2 : Front" Sub source (Auxiliary input source) is to be front channel. Other than Standby mode B.M.S. (Bass Management System) Adjust the bass boost level of the external amplifier using the main unit. Display Setting "AMP Bass : Flat" Bass boost level is flat. "AMP Bass : +6" Bass boost level is low (+6dB). "AMP Bass : +12" Bass boost level is mid (+12dB). "AMP Bass : +18" Bass boost level is high (+18dB). • Refer to the catalog or instruction manual for power amplifiers that can be controlled from this unit. • For amplifiers there are the model that can be set from Flat to +18 dB, and the model that can be set from Flat to +12 dB. When an amplifier that can only be set to +12 is connected to the unit, "AMP Bass : +18" won’t work correctly even if it’s selected. Other than Standby mode B.M.S. Frequency Offset Setting the central frequency boosted by B.M.S. Display Setting "AMP FREQ : Normal" Boost with the normal central frequency. "AMP FREQ : Low" Drop the normal central frequency 20%. English | 39 News Bulletin with Timeout Setting It switches automatically when a news bulletin starts even if the radio isn’t being listened to. Also, the time interval when interrupt is prohibited can be set. Display and Setting "News : OFF" "News : 00min" … "News : 90min" When "News : 00min" — "News : 90min" is set, the News Bulletin Interrupt function is ON. When the news bulletin starts, "News " is displayed, and it switches to the news bulletin. • If you choose the "News : 20min" setting, further news bulletins will not be received for 20 minutes once the first news bulletin is received. • The news bulletin volume is...
Otros modelos de este manual:Unidad - KDC-W7031 (1.9 mb)
Unidad - KDC-W7531 (1.9 mb)