Fabricar: Kenwood
Tamaño del archivo: 798.27 kb
Nombre del archivo:
|
Otros manuales para este modelo:
Resumen del manual
• After the unit is installed, check whether the brake lamps, indicators, wipers, etc. on the car are working properly. • If the console has a lid, make sure to install the unit so that the faceplate does not hit the lid when closing and opening. • Mount the unit so that the mounting angle is 30° or less. 28 | English 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 TEL MUTE P.CONT ANT.CONT FRONT Connecting Wires to Terminals Rear right output (Red)/ Subwoofer right output (Red) Rear left output (White)/ Subwoofer left output (White) Front left output (White) Front right output (Red) KENWOOD disc changer input Battery wire (Yellow) Ignition wire (Red) FM/AM antenna input Antenna Cord (ISO) Antenna Conversion Adaptor (ISO–JASO) (Accessory3) To connect the Disc changer, consult your Disc changer manual. To connect the KENWOOD navigation system, consult your navigation manual. Wiring harness (Accessory1) If no connections are made, do not let the wire come out from the tab. Power control/ Motor antenna control wire (Blue/White) TEL mute wire (Brown) Connect either to the power control terminal when using the optional power amplifier, or to the antenna control terminal in the vehicle. Connect to the terminal that is grounded when either the telephone rings or during conversation. A –7 Pin (Red) A–4 Pin (Yellow) Connector A Connector B Fuse (10A) See Next page. To External Display/ Steering remote English | 29 Connecting Wires to Terminals Connector Function Guide Pin Numbers for ISO Connectors Cable Colour Functions External Power Connector A-4 Yellow Battery A-5 Blue/White Power Control A-6 Orange/White Dimmer A-7 Red Ignition (ACC) A-8 Black Earth (Ground) Connection Speaker Connector B-1 Purple Rear Right (+) B-2 Purple/Black Rear Right (–) B-3 Gray Front Right (+) B-4 Gray/Black Front Right (–) B-5 White Front Left (+) B-6 White/Black Front Left (–) B-7 Green Rear Left (+) B-8 Green/Black Rear Left (–) 2WARNING Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit. The default connection for the wiring harness is described in 1 below. If the ISO connector pins are set as described in 2 or 3, make the connection as illustrated. Please be sure to reconnect the cable as shown 2 below to install this unit to the Volkswagen vehicles etc. 1 (Default setting) The A-7 pin (red) of the vehicle's ISO connector is linked with the ignition, and the A-4 pin (yellow) is connected to the constant power supply. Unit Vehicle A-7 Pin (Red) A-4 Pin (Yellow) Ignition cable (Red) Battery cable (Yellow) 2 The A-7 pin (red) of the vehicle's ISO connector is connected to the constant power supply, and the A-4 pin (yellow) is linked to the ignition. Unit Vehicle A-7 Pin (Red) A-4 Pin (Yellow) Ignition cable (Red) Battery cable (Yellow) 3 The A-4 pin (yellow) of the vehicle's ISO connector is not connected to anything, while the A-7 pin (red) is connected to the constant power supply (or both the A-7 (red) and A-4 (yellow) pins are connected to the constant power supply). Unit Vehicle A-7 Pin (Red) A-4 Pin (Yellow) Ignition cable (Red) Battery cable (Yellow) • When the connection is made as in 3 above, the unit's power will not be linked to the ignition key. For that reason, always make sure to turn off the unit's power when the ignition is turned off. To link the unit's power to the ignition, connect the ignition cable (ACC...red) to a power source that can be turned on and off with the ignition key. 30 | English Installation Screwing the Faceplate on the Unit If you want to fasten the faceplate to the main unit so that it does not fall off. 1 Refer to the section 'Removing the hard rubber frame' (page 32) and then remove the hard rubber frame. 2 Drop open the faceplate by pressing the Release button. 3 Tighten the screws (o2.6 . 12 mm) (Accessory 4) in the holes shown on the diagram. Accessory4 4 Tighten the screws (o2 . 4 mm) (Accessory 5) in the holes shown on the diagram. Accessory5 5 Tighten the screws (o2 . 6 mm) (Accessory 6) in the holes shown on the diagram. Accessory6 • Never insert the screws in any other screw hole than the one specified. If you screw them in another hole, it will contact and may cause damage to the mechanical parts inside the unit. • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Installation Firewall or metal support Screw (M4X8) (commercially available) Self-tapping screw (commercially available) Metal mounting strap (commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. English | 31 Removing the Unit Removing the hard rubber frame 1 Engage the catch pins on the removal tool and remove the two locks on the upper level. Upper the frame and pull it forward as shown in the figure. 2 When the upper level is removed, remove the lower two l...
Otros modelos de este manual:Unidad - KDC-W6027 (798.27 kb)