|
Otros manuales para este modelo:
Resumen del manual
(CDX-4000R/3900R only) • D.INFO (Dual Information) — to display the clock and the play mode at the same time (ON). • DIMMER — to dim the display (ON) or not (OFF). (CDX-4000RV only) • M.DSPL (Motion Display) — to turn the motion display on or off. • A.SCRL (Auto Scroll) (page 9) Note If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be disabled. Tip You can easily switch among categories ("SET", "DIS", "P/M" (play mode), and "EDT" (edit mode)) by pressing either side of (prst) for two seconds. 3 Press the (+) side of (seek/ams) to select the desired setting (Example: ON or OFF). 4 Press (enter). After the mode setting is completed, the display returns to normal play mode. 20 Boosting the bass sound — D-bass Additional Information You can enjoy a clear and powerful bass sound. The D-bass function boosts the low and high frequency signal with a sharper curve than conventional bass boost. You can hear the bass line more clearly even while the vocal volume remains the same. You can emphasize and adjust the bass sound easily with the D-BASS button. Adjusting the bass curve Press (d-bass) repeatedly until the desired bass level (1, 2, or 3) appears in the display. |—B D.BASS 1-► D I- n DA' BASS 2 -D.BASS-OFF b D.BASS 3 : Maintenance Fuse replacement When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. To cancel, select "D.BASS-OFF.” Warning Never use a fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit. Note If the bass sound becomes distorted, select a less effective setting of "D.BASS" or adjust the volume. 21 Cleaning the connectors The unit may not function properly if the connectors between the unit and the front panel are not clean. In order to prevent this, open the front panel by pressing (open) , then detach it and clean the connectors with a cotton swab dipped in alcohol. Do not apply too much force. Otherwise, the connectors may be damaged. \ 3 Use a thin screwdriver to push in the clip on the left side of the unit, then pull out the left side of the unit until the catch clears the mounting. 4 Repeat step 3 for the right side. Main unit Back of the front panel Notes • For safety, turn off the engine before cleaning the connectors, and remove the key from the ignition switch. • Never touch the connectors directly with your fingers or with any metal device. Dismounting the unit 1 After taking off the front panel, press the clip inside the front cover with a thin screwdriver, and gently pry the front cover free. 5 Slide the unit out of its mounting. 2 Repeat step 1 for the right side. The front cover is removed. 22 Specifications CD player section General Signal-to-noise ratio Frequency response Wow and flutter 90 dB 10 - 20,000 Hz Below measurable limit Tuner section FM Tuning range Aerial terminal Intermediate frequency Usable sensitivity Selectivity Signal-to-noise ratio 87.5 - 108.0 MHz External aerial connector 10.7 MHz/450 kHz 8 dBf 75 dB at 400 kHz 66 dB (stereo), 72 dB (mono) Harmonic distortion at 1 kHz 0.6 % (stereo), 0.3 % (mono) 35 dB at 1 kHz 30 - 15,000 Hz Separation Frequency response MW/LW Tuning range Aerial terminal Intermediate frequency Sensitivity MW: 531 - 1,602 kHz LW: 153 - 279 kHz External aerial connector 10.7 MHz/450 kHz MW: 30 LW: 40 ^V Power amplifier section Outputs Speaker impedance Maximum power output Speaker outputs (sure seal connectors) 4 - 8 ohms 50 W x 4 (at 4 ohms) Outputs Tone controls Power requirements Dimensions Mounting dimensions Mass Supplied accessories Optional accessories Audio outputs Power aerial relay control lead Power amplifier control lead Telephone ATT control lead* Bass ±9 dB at 100 Hz Treble ±9 dB at 10 kHz 12 V DC car battery (negative ground) Approx. 178 x 50 x 183 mm (w/h/d) Approx. 182 x 53 x 162 mm (w/h/d) Approx. 1.2 kg Parts for installation and connections (1 set) Front panel case (1) Rotary commander RM-X4S * CDX-4000RX/4000RV/4000R only Design and specifications are subject to change without notice. 23 Troubleshooting guide The following checklist will help you remedy the problems you may encounter with your unit. Before going through the checklist below, check the connection and operating procedures. General Problem Cause/Solution No sound. • Cancel the ATT function. • Set the fader control to the centre position for two-speaker system. • Rotate the dial clockwise to adjust the volume. The contents of the memory • The power cord or battery has been disconnected. have been erased. • The reset button has been pressed. —— Store again into the memory. Indications do not appear in the Remove th...
Otros modelos de este manual:Unidad - CDX-3900R (1.46 mb)
Unidad - CDX-4000R (1.46 mb)
Unidad - CDX-4000RV (1.46 mb)