Votos - 7, Puntuación media: 3.4
(
)
)
|
Resumen del manual
For details, refer to the following illustrated installation methods. DIN FRONT-MOUNT (Method A) 1. Car dashboard 2. Sleeve 3. Screw 4. Nut 5. Spring washer 6. Screw 7. Metal strap 8. Flat washer 5 1. 3. 4. 5. Install the sleeve into the dashboard; ensure it is installed with the correct side and there are no obstacles (wires, dashboard elements, etc) for the unit installation. After installing the sleeve into the dashboard, bend tabs fitting to the size of the dashboard to fix the sleeve in place. Use the metal strap to fix the rear side of the unit. Determine a place for fixing and install the strap as shown in the picture. You can bend the strap to the needed angle with your hands. Make the necessary wire connections. Ensure the connections are correct. Install the unit into the sleeve until the side locks are fixed. Dismantling the unit a - Trim frame 6 - Frame uninstall direction b - Release key insertion 1. Switch off the unit and detach the front panel. 2. Insert your fingers into the groove in the front side of the trim frame (apply some effort to detach the frame). Pull the frame to detach it. 3. Insert the supplied release keys into the both sides of the unit body to click, as shown in the picture. To extract the unit from the dashboard, pull the release keys or the unit body to pull it out. Before detaching the unit, ensure it is not fixed with the metal strap. Trim frame installation To install the trim frame, press it to the unit body and push it to fix it in place. This should be done before installing the front panel; otherwise you are not able to install the trim frame. When the trim frame being installed, the side with the groove should face down and fixed first. 2. DIN REAR-MOUNT (Method B) For this method, use the screw holes in the lateral sides of the unit. radio mounting brackets. 6 Fix the unit with the help of the factory 1. Select a position in which the screw holes of the brackets (3) are aligned with the screw holes in the unit body, and screw in two screws (2) in each side. 2. Screw. 3. Factory radio mounting brackets. 4. Vehicle dashboard. 5. Lock (remove this part). Note: The outer trim frame and mounting sleeve are not used for method of installation. Installing the front panel Insert the left side of the front panel into the unit locker so that lockers of the unit get into the fixing holes of the panel. Press on the right side of the panel until a click. Ensure the panel is fixed properly, otherwise error symbols may be displayed or some buttons will not function. To detach the front panel, press RELEASE button. Then pull the panel to take it out. Anti-theft system The front panel of this unit can be stored in the included protective case when not in used and carried away when you leave the vehicle to deter theft. Switch off the power of the unit. Detach the front panel, then put it to the protective case and take it with you. Cautions: The control panel can easily be damaged by shocks. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. The rear connector that connects the main unit and the control panel is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc. Note: If the control panel is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel. 7 Electrical connections Notes: • In spite of having any kinds of speaker system, must use 4 ohms impedance of speaker to reduce the distortion during high volume level. • Prohibit to make the conductors of auto antenna and ground touch with each other. 8 Using the ISO Connector 1. If your car is equipped with the ISO connector, then connect the ISO connectors as illustrated. 2. For connections without the ISO connectors, check the wiring in the vehicle carefully before connecting, incorrect connection may cause serious damage to this unit. Cut the connector, connect the colored leads of the power cord to the car battery as shown in the colour code table below for speaker and power cable connections. Location FUNCTION Connector A Connector B 1 Rear Right(+)---Blue 2 Rear Right(-)---Blue/White Stripe 3 Front Right(+)---Grey 4 Battery 12V (+)/yellow Front Right(-)---Grey/White Stripe 5 Auto Antenna/orange Front Left(+)---Green 6 Panel light/White Front Left((-)---Green/White Stripe 7 ACC+/red Rear Left(+)---Brown 8 Ground/black Rear Left(-)---Brown/White Stripe Panel light wire should be connected to "+" of the side parking lights wire. Power antenna wire is intended for power supply of the antenna and for remote control of an additional amplifier. 9 Control elements Front panel 1. SD/MMC card slot 2. MUTE button 3. VOL knob/SEL button 4. Disc slot 5. LCD display 6. UP/DN knob/MODE button 7. EJECT button 8. AF button 9. TA button 10....