Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
Rotate the VOL knob to select the desired mode: TA ALARM and TA SEEK. - TA SEEK When newly tuned station does not receive TP information for 5 seconds, the radio retunes to next station which has not the same station (PI - Program Information) as the last station, but has the TP information. When TP information gets lost at the current station for retune time which is set by RETUNE SHORT (30 seconds) or RETUNE LONG (90 seconds), the radio starts to retune to next same PI station. When same PI station does not catch in 1 cyclic search, the radio retunes to next station with TP information. - TA ALARM During searching the radio does not retune but the double beep sound (alarm) is output. • PI SOUND/MUTE 12 Choose PI sound or mute. PI sound refers to the reception noise when the AF function tries to scan alternative frequency. • RETUNE mode To determine the initial time of automatic TA (Traffic Announcement) search. There are 2 modes: RETUNE L and RETUNE L. - RETUNE L: 90 seconds. - RETUNE S: 30 seconds. Note: Retune mode is active for TA SEEK mode only. • MASK mode During AF search, PI stations and non-RDS (Radio Data Station) stations with strong signal will be masked, in the latter case, the non-RDS stations may cause interference, resulting the real AF to be masked due to the misjudgment of the radio under interference. Rotate the VOL knob to select the desired mode: MASK DPI and MASK ALL. - MASK DPI To mask only the AF with different PI. - MASK ALL To mask both PI and strong signal non-RDS station. • BEEP mode BEEP 2nd: the unit beeps only when any allowed double button is pressed longer than 1 sec. BEEP ALL: the unit beeps when any button is pressed. BEEP OFF: the beep is disabled. Mode selection Press MOD button to choose RADIO, AUX, CD source. Loudness control Press and hold BAND/LOUD button to turn the LOUD function ON or OFF. This function reinforces the bass output. Information display Press DISP button to operate as the conversion of each display mode as follows: 13 - In case of receiving a RDS station In radio mode: PS -> CT -> FREQ -> P TY In CD mode: CD -> CT -> (ID3 TAG) -> PS -> FREQ -> PTY * In case of no receiving CT or PTY Information, the display shows as "NO CLOCK" or "NO PTY". - In case of receiving a non RDS station In radio mode: "NO CLOCK" -> FREQ-> "NO PTY" In CD mode: CD -> "NO CLOCK" -> FREQ -> "NO PTY" Each displaying time is several seconds, and come back to 1'st position after several seconds. Notes: CT = clock time; FREQ = frequency. Equalizer setting Press EQ button to choose between the EQ sound effects: FLAT => CLASSICS => POP M => ROCK M => DSP OFF. 14 Radio operations Band selection Press the BAND/LOUD button repeatedly to select your desired radio band during RADIO mode: FM1, FM2, FM3, MW1. Automatic memory storing Press AMS button for 2 seconds, the radio searches from current frequency and checks the signal strength until one cycle is finished. And then 6 strongest stations are stored into the corresponding preset number button. Selecting station Press preset 1-6 button to select the station, which had been stored in the memory. Press the PREV/NEXT button for 2 seconds until "MANUAL" appears on the display, and then press the PREV/NEXT button to select a station. If both buttons have not been pressed for several seconds, they will return to automatic seek mode. Program scanning Press AMS button shortly to scan preset station. Station storing Press PREV/NEXT button to activate automatic seek mode. In manual mode, press PREV/NEXT button to select station. Press preset 1-6 button for 2 seconds to store current station into the number button. 15 RDS function Note: RDS (Radio Data System) service availability varies with areas. Please understand if RDS service is not available in you area, the following service is not available, either. Press AF/REG button to switch ON or OFF RDS function. Setting RDS mode Whenever RDS is switch on, symbol "AF" appears on the display. Program name is displayed on receiving a RDS station. "AF" starts blinking if the broadcasting signals getting worse. "ALARM" will be displayed when an emergency broadcasting is received; meanwhile sound output level will be adjusted to the preset output level automatically when the volume control is set at minimum. Regional Program Operation Press AF/REG button for 2 seconds to switch on or off region mode. Some broadcasting stations change their program from normal broadcasting to regional broadcasting for a certain time period. When region is on, the current listening program remains unchanged. When region is off, it allows the reception to move to the regional station. Using PTY to Select Program Press the PTY button repeatedly to select the PTY as follows: PTY MUSIC GROUP => PTY SPEECH GROUP => GROUP PTY OFF. When the PTY MUSIC GROUP or PTY SPEECH GROUP has been selected, press any of the preset numbered buttons repeatedly to search relevant P...