Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Rotate and hold the control, and release it to fast-wind the tape. To start playback while fast-winding the tape, press (MODE). • Locate a specific track on a disc. Rotate and hold the control until you locate the specific point in a track, then release it to start playback. • Tune in stations automatically. Rotate and hold the control to find a specific station. By pushing in and rotating the control (the PRESET/DISC control) Push in and rotate the control to: • Receive the stations memorised on the number buttons. • Change the disc. Other operations Rotate the VOL control to off the unit. Note When installing in a car without ACC (accessory) position on the ignition key switch, press (off) for two seconds to turn off the clock display after turning off the engine. 16 Press (dspl) to change the displayed items. Changing the operative direction The operative direction of controls is factory-set as shown below. To increase To decrease If you need to mount the rotary commander on the right hand side of the steering column, you can reverse the operative direction. Press (sel) for two seconds while pushing the VOL control. Adjusting the sound characteristics You can adjust the bass, treble, balance, and fader. You can store the bass and treble levels independently for each source. 1 Select the item you want to adjust by pressing (sel) repeatedly. Each time you press (SEL), the item changes as follows: BAS (bass) t TRE (treble) t BAL (left-right) t FAD (front-rear) 2 Adjust the selected item by pressing either side of the volume button. Adjust within three seconds after selecting the item. Attenuating the sound Press (Att). After “ATT-ON” momentarily flashes, the "ATT” indication appears in the display. To restore the previous volume level, press (ATT) again. “ATT-OFF” flashes momentarily. Tip When the interface cable of a car telephone is connected to the ATT lead, the unit decreases the volume automatically when a telephone call comes in (Telephone ATT function). 17 Changing the sound and display settings The following items can be set: • CT (Clock Time) (page 15). • A.SCRL (Auto Scroll)* (page 20). • M.DSPL (Motion Display) - the demonstration mode which appears when the tape is ejected and no source is selected (e.g., tuner is turned off). • BEEP - to turn the beep sound on or off. Selecting the desired item Press (sel) and the desired preset number button simultaneously. (Set) + (2): CT (Set) + (3): A.SCRL* (Set) + (4): M.DSPL (Set) + (6): BEEP * When no CD or MD is playing, this item will not appear. After the mode setting completed, the display returns to normal play mode. Note The displayed item will differ depending on the source. To cancel the item, press (SEL) and the preset number button simultaneously again. Boosting the bass sound — D-bass You can enjoy a clear and powerful bass sound. The D-bass function boosts the low frequency signal and high frequency signal with a sharper curve than conventional bass boost. You can hear the bass line more clearly even while the vocal volume remains the same. You can emphasize and adjust the bass sound easily with the D-BASS button. Press (d) repeatedly to select the desired bass curve. As the D-BASS number increases so does the effect. D.BASS-1 t D.BASS-2 t D.BASS-3 t D.BASS-OFF Note The bass sound may distort at same volume. If the bass sound distorts, select less effective bass curve. 18 Selecting the listening position — "My Best sound Position” When you drive without passengers, you can enjoy comfortable sound environment by “My Best sound Position.” “ My Best sound Position” has two presets, which adjust the sound level of balance and fader. You can select one very easily with MBP button. With Optional Equipment CD/MD Unit This unit can control external CD/MD units. If you connect an optional CD unit with the CD TEXT function, the CD TEXT information will appear in the display when you play a CD TEXT disc. Display window Balance Level Fader Level Right Left Front Rear MBP-A - 4dB 0 0 - 4dB MBP-B 0 - 4dB 0 - 4dB MBP-OFF 0 0 0 0 Press (mbp) repeatedly until the desired listening position. Mode of "My Best sound Position” will be shown in the display in order of the table. Playing a CD or MD 1 Press (src) repeatedly to select CD or MD. 2 Press (mode) until the desired unit appears. CD/MD playback starts. When a CD/MD unit is connected, all the tracks play from the beginning. Fun After one second, the display goes back to the normal playback mode. If you want to adjust the sound level of balance and fader more precisely, you can do it in (SEL) button (See “Adjusting the sound characteristics” on page 17). Changing the display item Each time you press (dspl) during CD, CD TEXT, or MD playback, the item changes as follows: I V Elapsed playback time i V Disc name*1/Artist name*2 V Track name*3 V Clock *1 If you have not labelled the disc or if there is no disc name...
Otros modelos de este manual:Unidad - XR-CA400 (1.29 mb)