Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
The radio frequency of the remote controls is fixed and tuned at the factory; adjustments are not required and should not be attempted by the end user. WARNING Keep transmitters and remote controls out of the reach of children. Do not let children play with or use the transmitter or remote controls. Unexpected door operations can cause personal injury or property damage. Do not place transmitter where the buttons can be accidentally or unintentionally activated. Features of the Quik-Code Wireless Keyless Entry On/Reset Key: This key turns on the keypad and light system allowing you to operated the system as well as to see the keys in the dark. The keypad will remain lit for 20 seconds after the last key is pressed. Single Button Mode: Once you have entered a valid PIN and your door operator begins to function, the number keys remain active for 20 seconds. Pressing any one of these keys sends another signal to the operator and allows you to stop and start the door operator. Low Battery Indicator: The lighting for your keypad also serves as a low battery indicator. When the keypad lights flash on and off the battery should be replaced with a standard 9 volt battery. Non-Volatile Memory: It is not necessary to reprogram the keypad after you replace your battery. Allstar MVP Quik-CodeTransmitters and Receivers are compatible with HomeLink®. HomeLink® is a registered trade mark of Johnson Controls. W ARNING Unexpected door operations can cause personal injury or property damage. Mounting the Quik-Code Wireless Keyless Entry Step 1: Choose a convenient location that does not interfere with the normal opening and closing of the door. Keep in mind that some doors swing outward and will damage an improperly located keypad. MOUNT THE KEYPAD A MINIMUM OF 5 FEET ABOVE THE GROUND TO KEEP IT OUT OF REACH OF CHILDREN. Step 2: The screws provided are adequate for mounting directly to wood or similar material. When mounting on masonry or similar material plastic anchors are recommended. Drill a hole for the bottom screw. Install the screw leaving the head of the screw approximately 1/8 inch out from the wall. Slide the keypad over the screw and mark the position of the top hole. Remove the keypad and drill the top hole. Slip the keypad back over the exposed screw and finish mounting by installing the top screw. Refer to Figure 1. MOUNT THE KEYPAD IN A LOCATION THAT MINIMIZES THE POTENTIAL FOR THE USER TO COME IN CONTACT WITH A MOVING DOOR. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. W A R N I N G Disconnect power to the operator before and during installation. Do not reconnect power until the mounting is complete. Ensure doorway is clear before testing the operation of the wireless keyless entry. Programming the Quik-Code Wireless Keyless Entry When set to learn mode, the MVP receiver memorizes a PIN entered from the keypad. Once learned, this PIN activates the MVP operator. Choose a four digit PIN that is easy to remember but not obvious. Avoid using house numbers, phone numbers or numbers that are easy to guess. The letters marked on the keypad may be used to help remember your PIN. For example, 6-9-7-3 or N-Y-P-D. GHI * PRS 7 4 1 0 # ON RESET DEF 6 MNO 9 WXY 3 8 TUV ABC 5 JKL 2 Figure 1 Mounting Battery Holes Hatch GHI * PRS 7 4 1 0 # ON RESET DEF 6 MNO 9 WXY 3 8 TUV ABC 5 JKL 2 Programming Steps for Quik-Code Wireless Keyless Entry Step 1: The red Keypad lighting should be Off. If it is on, wait until it turns off (approximately 20 seconds). Step 2: Using the end of a paper clip, put the receiver of the MVP Into Learn Mode by pressing and quickly releasing the recessed learn button located on the super deluxe wall station. The work-lamp on the MVP will turn on (or blink off then on) to indicate the receiver is ready to learn a code. You have approximately 30 seconds to enter the keypad PIN and door code. Step 3: Press ON/RESET to turn on the keypad. The red lighting on the keypad will turn on. Step 4: Enter your Four Digit PIN. Every time you press a key the keypad lighting system will blink off and on to verify a key has been pressed. Step 5: The work-lamp on the MVP will turn off when a valid PIN has been learned. For example, once the MVP is in learn mode you press the following keys: ON/RESET 6 9 7 3. Using the Quik-Code Wireless Keyless Entry To operate the keypad press the RESET/ON, enter your PIN. If you make a mistake while entering your PIN press the RESET/ON and wait about 2 seconds and enter the correct PIN. The numbered keys will remain active for approximately 20 seconds after the door starts to move. Pressing any one of the numbered keys during this time will allow you to stop and restart the door’s movement. For example, press the following k...