Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
INSTALLATION Unplug the power cord of your garage door opener WARNING before installation to ensure power is not connected. GTR Smart ButtonTM The GTR Smart ButtonTM replaces most garage door “push buttons” or “wall consoles”. There are 2 different kinds of “push buttons”. 1) Single button 2) Multi-Function Wall Console 1) Single button If your garage door opener comes equipped with a single button “push button”, you can replace the existing push button with Skylink® Smart ButtonTM GTR. Please follow the procedures below. 1. Remove the existing push button by removing the screws. 2. Disconnect the 2 wires that are connected to the existing push button. 3. Connect the 2 wires from the existing wall button to the GTR Smart ButtonTM. Twist the 2 wires together with the wire connector provided. Polarity does not matter, so simply pick one wire from the existing wall button, and connect it to one of the wires on the Smart ButtonTM. Do the same for the 2nd wire. 4. After connecting the wires, mount the Smart ButtonTM on to the wall with 2 screws. 5. Plug in the AC cord of the garage door opener. The red light on the Smart ButtonTM should flash 15 seconds after plugging in the power. The red light will not flash immediately after plugging in the power, which is normal. The Smart ButtonTM is now ready to be operated. Note: Straighten up the antenna to improve signal reception. Remove existing wires Mounting Accessories 2. INSTALLATION (CONT) Smart ButtonTM 2) Multi-Function Wall Console Multi-Function Wall Console normally comes with 3 buttons that can be used to: 1) operate the garage door opener lighting, 2) lock the receiver so it doesn’t accept remote control operation, and 3) push button for door opening / closing Congratulations on your purchase of the Skylink® G6KR Universal Garage Door Remote Control. This is a kit with a universal keypad transmitter and Smart ButtonTM. It is 100% compatible with all garage door openers. Simply replace the traditional wall button by the Smart ButtonTM, that’s all for the installation. In this kit, you will find the following: Rating of the transformer: 12V DC, 100mA Diameter of DC plug : 3.5mm Note: Straighten up the antenna to improve signal reception. If you have the multi-function wall console, do not replace the wall console by the Smart ButtonTM. You need to install the Smart ButtonTM in parallel with your existing wall console. 1. Remove the existing wall console from the wall by removing the screws. 2. Remove the 2 screws that secure the wires on the wall console. 3. Connect the wires from the Smart ButtonTM to the existing wall console. Polarity does not matter, so simply pick one wire from the Smart ButtonTM, and connect it to one of the terminals on the existing wall console. Do the same for the 2nd wire. 4. After connecting the wires, mount the Smart ButtonTM on to the wall with 2 screws. Also mount the original wall console on to the wall. 5. Plug in the AC cord of the garage door opener. The red light on the Smart ButtonTM should flash 15 seconds after plugging in the power. The red light will not flash immediately after plugging in the power, which is normal. The Smart ButtonTM is now ready to be operated. 6. If the Smart ButtonTM red light does not flash at all 2 minutes after plugging in the AC cord, your garage door opener is probably too old. However, the Smart ButtonTM will still work by plugging in an adapter (purchase separately). Please contact Skylink® to purchase the adapter. If the red light on the Smart ButtonTM is flashing slowly, that indicates it is in standby mode. When a valid remote control signal is received, it will open / close the garage door. Simply press the button on the Smart ButtonTM, it will open / close the garage door. OPEN / CLOSE 3. OPERATION Antenna 2 Wire Connectors Universal Keypad Transmitter (Battery included) - To change your PIN: 1. Enter the current PIN, (currently set at 0 0 0 0), press , 2. Enter new 4 digit PIN, press , 3. Enter new PIN again, press . For example, if you are changing the PIN number from 0000 to 1234, enter the following sequence, 0000, ,1234, ,1234, . If confirmed, the backlit LED flashes and the unit emits a long beep. * * * * * * - Operation Press [ PIN ] , [#] To open or close garage door, press your four digit PIN and the [#] key. If confirmed, the keypad transmitter will emit three beeps. Default PIN is 0000. Press [0000][#] to open the garage door. If you do not hear 3 beeps after the 4-digit PIN and [#] is entered, that means you have entered an incorrect PIN, and the keypad transmitter will not operate your garage door. 33.. OOPPEERRAATTIIOONN ((CCOONNTT)) 8.. WWAARRRRANNTTYY Programming Learn additional remote controls Smart ButtonTM can learn up to 15 remote controls. To learn additional remote controls, follow the instructions below: 1. Press the learn button on the side of the GTR. 2. Once the learn button is pressed, the LED will flash quickly. You may release the learn button. 3. Enter [...