Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
First use the double sided tape to attach the mounting bracket on the windshield or use the visor clip to clip the mounting bracket on the visor, then you can put the remote control on the bracket. The remote control can also be attached to your key ring as a key fob. 7. TRANSMITTER MOUNTING METHOD 6. Power up the garage door opener, the red LED on the Smart ButtonTM GB-318 should keep flashing slowly within 2 minutes. LED 2. RECEIVER INSTALLATION (CONT) If the Smart ButtonTM GB-318’s red LED does not flash after the Smart ButtonTM GB-318 has been connected to the wall button’s wires for 2 minutes, your garage door opener is probably too old. However, the Smart ButtonTM GB-318 will still work if you plug in an adapter (purchased separately). Please contact Skylink® to purchase the adapter. 77.. TTRRAANNSSMMIITTTTEERR MMOOUUNNTTIINNGG MMEETTHHOODD ((CCOONNTT)) 99.. OPPTIONAL ACCESSOORIIES AANNDD OPPERRATIOONNS Mounted on the windshield Stick the Peal off the double sided tape cover. double sided tape on the back of the bracket. Mounted on the visor Attach visor clip to bracket. 8. TRANSMITTER PASSWORD PROTECTION Password protection The G6T3 can be password protected. If you enable the password protection, you can only operate G6T3 after you input the correct password. Password can be 2-8 digits long, which is a combination of 1, 2 and 3. For example, password can be 1, 2, 1, 2. To input this password, you have to press [ ], then [ ], then [ ], then [ ]. Note: [ ] = Button 1 [ ] = Button 2 [ ] = Button 3 Button [ 1 , 2, 3 ] Note: The time-out period is 1 second during above password input. The factory default password is 2, 2, 2, which is disabled out of factory. Change password 1. Press 1 and 3 simultaneously and hold for more than 6 seconds until the LED changes from flashing quickly to flashing slowly. 2. Input old password. 3. Press 1 and 3 simultaneously to confirm. If the password is wrong, the LED will flash 3 times and you have to start it over from step1. 4. Input new password. 5. Press 1 and 3 simultaneously to confirm. 6. Input new password again. 7. Press 1 and 3 simultaneously to RE-confirm. If the password is different from the one of step 4, the LED will flash 3 times and you have to start over from step 1. Otherwise, the password has been changed to the new one and the password protection is enabled. Disable password 1. Press 1 and 3 simultaneously and hold for more than 2 seconds until the LED flashes quickly but not until the LED flashes slowly. 2. Input old password. 3. Press 1 and 3 simultaneously to confirm. If the password is correct, the password protection will be disabled. Enable password 1. Press 1 and 3 simultaneously and hold for more than 2 seconds until the LED flashes quickly but not until the LED flashes slowly. 2. Input old password. 3. Press 1 and 3 simultaneously to confirm. If the password is correct, the password protection will be enabled. You can toggle the two states - password protection enabled or disabled. Note: The time-out period is 10 seconds during any of the above setting operations. After 10 seconds, the LED will flash 3 times and the remote will exit from setting. If you forget your password and want to reset G6T3, follow the steps below: 1. Press 1 and 2 simultaneously and hold for more than 10 seconds until the LED flashes. 2. After you release 1 and 2, the LED will be turned off and G6T3 will be reset. The password will be reset to factory default. After the reset, password protection is removed but the remote can not control any receiver until you reprogram it to receivers you want to control. You can add up to 10 additional transmitters to control the GB-318. Skylink® offers different lighting control / automation transmitters, Visor Transmitters, Keychain Transmitters and Keypad Transmitters to work with your receiver. Program additional remote controls Smart ButtonTM GB-318 can learn up to 10 remote controls. To learn additional remote controls, follow the instructions below: 1. Press the learn button on the side of the GB-318. 2. Once the learn button is pressed, the LED will flash quickly. Release the learn button. LED 3. Within 30 seconds, press the button on the remote control you would like to program. 4. Once the remote control is programmed, the LED will flash slowly, in the same way as it flashes in standby mode. 5. You may now operate the garage door opener Learn Button with this remote control. For more information, please visit our website at or contact us. 10. BATTERY 3 Volt lithium battery (CR 2032) (included). It is time to change the battery when the red LED on the transmitter does not turn on when either button is pressed. 11. WARNING DO NOT let children use the garage door transmitter without adult supervision. Otherwise, Children and others may be injured by the garage door. 12. FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause...