Votos - 4, Puntuación media: 4.8
(
)
)
|
Resumen del manual
User Guide FOLLOW THESE INSTRUCTIONS CAREFULLY AND KEEP THEM FOR FUTURE REFERENCE This gate is designed for children from 6 months to 36 months. Since each child’s skills develop at different ages, these age parameters should be monitored against your child’s own development. Intended for use with children from 6 months through 36 months. Check and tighten all hardware and mountings regularly. To prevent serious injury or death, securely install gate or enclosure and use according to manufacturer’s instructions. Never use with a child able to climb over or dislodge/open the gate or enclosure. Never use if gate is 3/4 child’sheight. Do not use if any part of gate isbroken or missing. This product will not neccessarily prevent all accidents. Never leave child unattended. Use only spare parts from KidCo. Never allow child to climb or swing on gate. Use only with the locking/latching mechanism securely engaged. Closely supervise child when gate is installed at the top of thestairs. Hinge Side Hardware Locking Side Hardware 2 Hinge bottoms (c) 2 Locking latches (e) 2 Hinge spindles with locknuts (I) 2 Locking latch brackets 2 Springs (k) 1 Bottom latch spindle 6 1/4" (m) 2 Hinge caps (d) Latch spindleHinge already fitted (q) General Hardware ) 1 Main gate section with door opening (n) 8 Wood screws (g) 1 Protective plastic cover (h) 4 Expansion screw sockets (i) 1 Second Section (o) 4 Expansion screws (j) 1 Stabilizing foot (p) 1 Hinge side template (a) Templates are precise. Due to size they are not intemet reproducible. Please contact customer service for replacement templates. 1 Wrench (q) 1 Locking side template (b) . 4 important: Gate must be installed in a structurally sound opening. Hinge side of gate must be mounted to a rigid surface. Ensure mounting surface (wall, door frame, stairpost etc.) is strong, rigid and has an even surface. If using gate on a stairway it must be placed either on top stair or on lowest stair at bottom. If using on a top step, use of an optional step plate is recommended to reduce tripping potential. Mounting Hinge Side Screws provided are for mounting directly into wood. If mounting into brick, drywall or other surfaces, use appropriate hardware. If installing into hardwood (i.e. oak), drilling a pilot hole may be necessary. Hold template (a) against mounting surface, making sure end marked is even with floor. Mark 4 screw hole positions. Remove template. Using 2 wood screws (g) and only lower screw holes, mount hinge bottoms (c) with posts pointing up. Top screw holes will be used later. Screw hinge spindles (I) into top and bottom rails of second section (o) until they are extended equally. These will be adjusted to correct length at a later stage so do not tighten. Mounting Locking Side Screws provided are for mounting directly into wood. If mounting into brick, drywall or other surfaces, use appropriate hardware. If installing into hardwood (i.e. oak) drilling a pilot hole may be necessary. Hold template (b) against mounting surface in line with opposite hinges, making sure end marked is even with floor. Mark 4 screw hole positions. Remove template. Fit a locking latch (e) into locking latch bracket (f) and using 2 screws, screw into lower set of screw holes. Fit remaining locking latch (e) into remaining locking latch bracket (f). Determine which direction gate should open. For stairways, gate should never open out over stairs. As an added safety measure, a stop pin has been provided. Inset-t stop pin (r) from behind locking latch bracket into hole opposite gate opening direction. Using 2 wood screws,screw into upper set of screw holes. Push bottom latch spindle (m) into lower rail of main gate section (n). 6 The correct width will be reached by adjusting gate sections and all four corner spindles. Each spindle adjusts individually and may be extended to varying lengths to allow for molding, uneven walls, etc. Spindles may be extended a minimum af 1” but not more than 4” on each side. Adjust gate sections until gate is approximately right width and adjustment holes are aligned top and bottom. Sections should fit without any distance between bars. Gate sections must not be extended any further than 4 adjustment holes from spindl...
Otros modelos de este manual:La puerta automática - G60 (553.01 kb)