Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
If the system engages with the door in the open position, personal items that are left unattended in the garage or home are at risk to theft. To insure the safekeeping of these items, close the garage door. Typical signs of an engaged system: Single spring system: Visually inspect the TorqueMaster® Plus right hand end bracket to confirm that the system has engaged (see illustration). If the system is engaged then the door will not close. If the opener force settings were properly set during the initial installation, the door will not open. If the opener can physically overcome the weight of the door and lift it to the open position, then the counterbalance cables will be slack. WARNING WARNING Tools Needed: 30 Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages/business listings or go to the Find a Dealer section online at place vice clamps BELOW BOTTOM SECTION on both vertic al track Pawl Knob in Lower Position Pawl knob in UPPER Position Lower Position UPPER Position TorqueMaster® Plus Reset Instructions Continued... PAWL End Bracket Ratchet with 5/8” Socket 3” Extension If the system is engaged, DO NOT attempt to make the repairs. Instead, have a trained door system technician make the necessary repairs to cables, spring assemblies and other hardware. Double spring system: Visually inspect the TorqueMaster® Plus end brackets to confirm that the system has engaged (see illustration). Door will open, but will not close. Door makes a distinct “clicking” noise upon being opened. If the system is engaged, carefully follow the reset instructions below or refer to the reset tag (attached to right hand end bracket) to reset the TorqueMaster® Plus system. RESETTING AN ENGAGED TORQUEMASTER® PLUS DOUBLE SPRING SYSTEMS ONLY : 1. First, locate and visually inspect the TorqueMaster® Plus end brackets to confirm that the system is engaged (see illustration). 2. Disengage the opener (if installed) by pulling or placing the emergency disconnect in the manual operated position. 3. With assistance, raise the door to the fully open position. 4. Place vice clamps onto both vertical tracks just below the bottom roller on both sides. 5. Now is a good time to remove vehicles or personal items from garage to provide clear access to end brackets. 6. Flip the ratchet pawl knob on both end brackets to the upper position (see illustration). 7. Raise door 2”-3” and then lower door. Repeat this process until the system resets (see disengaged system illustrations). IMPORTANT: BE PREPARED TO SUPPORT THE TOTAL WEIGHT OF THE DOOR. 8. Cautiously remove the vice clamps from the vertical tracks. With assistance, lower door. CHECKING SPRINGS FOR TENSION: 9. Starting on the right hand side, place a ratchet wrench with 5/8” socket on the TorqueMaster® Plus winding shaft (see illustration). Ensure ratchet is set so that it will tighten counter clockwise on the right hand side, and clockwise on the left hand side. If tension is present, remove the ratchet and check the left hand side. If springs have tension, proceed to the paragraph titled BALANCING DOOR; if no spring tension is present, contact a qualified door systems technician to replace the spring(s). IMPORTANT! TO AVOID POSSIBLE INJURY, HAVE A TRAINED DOOR SYSTEM TECHNICIAN MAKE ADJUSTMENTS/ REPAIRS TO CABLES, SPRING ASSEMBLIES AND OTHER HARDWARE. .. Tools Needed: 31 Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages/business listings or go to the Find a Dealer section online at vice clamps Track attached to inner rail of track place vice clamps above 3rd Roller on both vertic al track Pawl knob in Lower Position Lower Position UPPER Position TorqueMaster® Plus Reset Instructions Continued... Pawl knob in upper Position PAWL End Bracket Ratchet 5/8” Socket 3” Extension BALANCING DOOR: Lift the door and check its balance. Adjust springs, if door lifts by itself (hard to pull down) or if door is difficult to lift (easy to pull down). Anytime spring adjustments are made, ratchet pawl knob must be in the upper position (see illustration). An unbalanced door can cause idrive® or Torquemaster® Plus operation problems. IMPORTANT! TO ADJUST SPRINGS, ONLY ADD OR REMOVE A MAXIMUM OF 3/10 OF A TURN (THREE TEETH ON THE RATCHET WHEEL) AT A TIME. BOTH SIDES NEED TO BE ADJUSTED EQUALLY ON DOUBLE SPRING DOORS. Close the door and place vice clamps onto both vertical tracks just above the third roller. This is to prevent the garage door from raising while adjusting the counterbalance spring(s). Prior to winding or making adjustments to the springs, ensure you’re winding in the proper direction as stated in the Installation Instructions. Otherwi se, the spring fittings may release from spring if not wound in the proper direction and could result in sev...