Votos - 2, Puntuación media: 5
(
)
)
|
Resumen del manual
NOTE • Little effort is required to turn the Force Adjusting Knobs. • If the door stops moving while opening or closing, adjust the Open Force or Close Force Controls slightly clockwise (to slightly increase the force) and retry the step. • The Open Force and Close Force Controls are to be set to the minimum force necessary to ensure the door smoothly opens and closes completely. • Ensure the Carriage Assembly is engaged and is between the two Limit Switches before operating the Opener. Figure MA-1 Making Force Adjustments OPEN CLOSE OPEN CLOSE FORCE CONTROLS Maintenance and Adjustments Figure MA-2 Making Force Adjustments OPEN CLOSE OPEN CLOSE 8 For Help, call 1-800-35-GENIE or visit A To program one Button of a Remote Control (Figure MA-4): • Locate Learn Button and Learn Indicator Light on left side of Power Head (Figure MA-5). • Press and release Learn Button. Red Learn Indicator Light will blink 2 times per second. • Press Remote Control Button once within 30 seconds. Red Learn Indicator Light will stay lit. • Press Remote Control Button again. Red Learn Indicator Light will go out, indicating that memory is stored. B Program each additional Remote using step A above (up to seven). NOTE • Each Remote Control must be programmed separately. • The Remote Controls will not cause the door Opener to close the garage door if the Safe-TBeam ® System is malfunctioning. • When programming the Remote Controls, they must be at least 24” from the Antenna Wire. • If the red Learn Indicator Light blinks approximately 4 times per second, programming has stopped. If programming has stopped, repeat the above steps. • Each Button on a 2 or 3 Button Remote Control is for a different Opener. You cannot use more than one Button per Remote, per Opener. • A maximum of seven Remote Controls or Wireless Keypads can be stored into the Receiver at one time. If a Remote Control becomes lost, or if you want to delete a Remote Control or Wireless Keypad, see “To Erase All Receiver Memory.” C Progr amming the Remote Controls Programming 1: Acc ess ories To Erase All Remotes from Power Head Memory A Press and hold Learn Button on Power Head for 10 seconds or until Learn Indicator Light goes out. Memory is erased: • Program Transmitter/Receiver again as needed. To Replace Remote Control Battery A FOR NON-FLASHLIGHT MODELS • Pop off the back of the transmitter. – Use coin, pen, screwdriver or any similar device. – Replace old Battery with new coin type battery. • Replace back of remote. B FOR FLASHLIGHT MODELS • Slide open battery cover. – Replace old Battery with new AAA battery. • Replace battery cover. A Open garage door using Wall Console. B Lay a 2” x 4” board flat in center of doorway. C Close door using Wall Console. D Check that door stops and reverses within 2 seconds after it contacts board: • If door does not reverse, decrease Close Force until door reverses. • If door still does not reverse, move Limit Switch toward door. E Check Safe-T-Beam® System operation: • If beam is blocked, door will not close. NOTE The door must contact the 2” x 4” board before the Carriage activates the Close Limit Switch. If not, readjust the Close Limit Switch. Ch Setting Contact Revers e Function Adjustment 2: NOTE Limit Switch and Force Adjustments must be completed before checking the contact reverse function (Figure MA-3). 2” x 4” board laid flat Figure MA-3 Transmitter Compliance Statement For Help, call 1-800-35-GENIE or visit 9 Remote Control Operation A Press Button on Remote Control. Garage door will move. B Press Button again. Garage door will stop: • The door automatically stops at the end of the open or close cycle. C Press Button again. Garage door will reverse. WARNING: A moving garage door may cause serious injury or death. • Keep people clear of opening while door is moving. • Do not allow children to play with the Remote Controls. If the Safety Reverse does not work properly: • Close the door and disconnect the Opener using the Emergency Release Cord. • Do not use the door Opener, Remote Controls, or Wireless Keypad. • Refer to the door and door Opener Owner’s Manuals before attempting any repairs. 1 2 3 4 FiFgiugruer Me 1A3-5L eLaeranrnC Coodde eB uButttotonn a nadnd In Idndiciactaotro Lr iLgihgtht 1 Button Compact Remote w/Docking Station Figure MA-4 Genie Remote Controls 3 Button Compact Remote w/Docking Station A Install two 60 Watt light bulbs (not included) into Light Sockets (Figure MA-6): • Rough service, 130 Volt bulbs are recommended. B Hold the lens, with the bottom hinges pointing up, against the power head metal front cover (Figure MA-7). • Insert (2) #8-32 x 3/8” Phillips Hex Head Screws through the Bottom hinges and into holes provided in metal front cover of Power Head (Figure MA-7). Tighten screws. • Flip Lens up and fasten with (2) #8-32 x 3/8” Phillips Pan Head Screws where indicated. Figure MA-7 Figure MA-6 Install Light Bulbs and Lens WARNING: Use the Wall Console inc...
Otros modelos de este manual:La puerta automática - DirectLift 2060 (1.56 mb)