Votos - 4, Puntuación media: 3.3 ( )

Fabricar: Craftsman Tamaño del archivo: 1.86 mb Nombre del archivo: Idioma del manual:

The door control is typically attached directly to the wail. If installing into drywall, drill 5/32" holes and use the anchors provided. For pre-wired installations (as in new home construction), Console models may be mounted to a.standard single gang box (Figure 2). 1. Strip 1/4" of insulation from one end of the bell wire and connect it to the two screw terminals on the back of the door control: white to 2 and white/red to 1. 2. Door Control Button: Fasten securely with 6ABx1-1/2" screws. Console Model: Pry off cover along one side with a screwdriver blade (Figure 1). Fasten with 6ABx1-1/4" self-tapping screws (standard installation) or 6-32x1" machine screws (pre-wired installation) as follows: • Install bottom screw, allowing 1/8" to protrude above wall surface. • Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit. • Install top screw with care to avoid cracking plastic housing. Do not overtighten. • Insert top tabs and snap on cover. 3. (For standard insta/lation only) Run the bell wire up the wall and across the ceiling to the opener. Use insulated staples to secure the wire in several places. Be careful not to pierce the wire with a staple, creating a short. 4. Connect the bell wire to the terminal screws on the opener panel: white to 2; white/red to 1. 5. Positionthe antenna wire as shown. DOOR PREMIUM CONTROL CONTROL STANDARO CONTROL BuTroN CONSOLE CONSOLE BackPanel orOpener Do not connect to live electrical widng. Connect only to 24 Volt low voltage wires. Connection to live wires or higher voltage may cause serious injury from shock, burn or electrocution. Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Install the door control (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, but where the garage door is visible. Do not allow children to operate the push button(s) or the remote control(s). A moving garage door could injure someone under it. Activate the opener only when the door is properly adjusted, you can see It clearly, and the.re are no obstructions to door travel. Hardware Shown Actual Size DoorControlButton 6ABx 1-1/2"Screw Contxo4Console(std instaltadon) Staples ControlLore-wired) ConsoleDryWa_Anchom Figure 1 Figure 2 REMOVE & REPLACECOVER PRE-WIRED INSTALLA'RON 24 Volt 2-Conducto. BellWire STANDARD CONTROL (BACKVIEW) Top T_nal DOOR CONTROL BUTTON (BACK) PREMIUM CONTROL (BACKVIEW) Top Wire TerminalScrews _ Te_Nnal _1 ''_=_ >scfewt Be.. [.__ .Mou_ng HO_ W'ffm _. 18 6. Attach the User Safety Instruction label to the wall neat the door control, and the Maintenance Instruction label in a prominent location on the inside of the garage door. Page 32 explains how to use the door control. , r Do NOT connect the power and operate the openerat this time. The trolley will travel to the full open position but wilt not return to the close position until the sensor beam is connected and properly aligned. See Safety Reversing Sensor instructions beginning on page 21. Installation Step 7 Install the Light and the Lens Install the light: • Install a 75 watt maximum light bulb in each socket. The lights will turn ON and remain lit for approximately 4-1/2 minutes when power is connected. Then the lights will turn OFF. • If the bulbs bum out prematurely due to vibration, replace them with standard neck "Garage Door Opener =bulbs. Install the lens: • Apply slight pressure on the sides of each lens and slide the tabs into the slots in the side panels. ', For convenience, the lens may be Installed after Adjustment Step 4 on page 30. • Reverse the procedure to remove the lenses. Installation Step 8 Attach the Emergency Release Rope and Handle I Do not use the red handle to pull the door open or closed. The rope knot could become untied and you could fall. Use the emergency • Thread one end of the rope through the hole in release only to disengage the trolley and, if the top of the red handle so "NOTICE" reads dght possible, only when the door Is closed. side-up a_shown. Secme with an overhand knot. Garage doors are heavy. _t the door is open The knot should be at least 1" from the end of when the handle is pulled, the door could the rope to prevent slipping. close inadvertently if it Is not properly :• Thread the other end of the rope through the hole balanced. Serious Injury may result to persons in the release arm of the outer trolley. under the door. Make sure the doorway is clear of persons and obstructions before pulling • Adjust rope length so the handle is 6 feet above handle when door is open. the floor. Secure with an overhand knot. r If it is necessary to cut the rope, heat seal the cut end with a ma_ch or lighter to prevent unraveling. P.ekmseAnn Rem Handle 19 Installation Step 9 Electrical Requirements To reduce the risk of electric shock, your garage door opener has a grounding...

Descargar ahora

Introduzca dos números de la imagen: