Iniciar sesión:
Votos - 3, Puntuación media: 4.7 ( )

Manual de usuario Wayne-Dalton, modelo PRODRIVE 3221C-Z

Fabricar: Wayne-Dalton
Tamaño del archivo: 4.85 mb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


CAUTION: Over tightening the screws could deform plastic case. FORCE ADJ. PROGRAMSW STATUS IMPORTANT: CONNECT THE LOW VOLTAGE WIRE TO THE WALL STATIONS USING A “J” HOOK CONFIGURATION. IF WIRE IS COMPLETELY LOOPED AROUND TERMINAL SCREW, IT CAN PREVENT PROPER CONTACT. Wall Station Back Phillips Head Screws Wall Station Front Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at 7 9 Deluxe Multi-Function Wireless Wall Station Installation (If Included) Tools Needed: Power Drill 3/32” Drill Bit Phillips Head Screwdriver TO PREVENT POSSIBLE INJURY, INSTALL WALL STATION OUT OF THE REACH OF CHILDREN AND IN A LOCATION WHERE THE DOOR CAN BE SEEN WHEN THE OPENER IS ACTIVATED. DO NOT MOUNT WALL STATION NEAR OR NEXT TO GARAGE DOOR. NOTE: For proper operation, mount the wall station on a flat surface. The wall station can be mounted to a NEMA standard electrical box or directly to any wall surface. No wiring is required. Locate wall station adjacent to service entrance door at a minimum height of 5 ft., and at least 6 ft. away from garage door. If mounting to a NEMA electrical box, use machine thread screws provided in place of the wood screws. No drilling is required. If high voltage wiring is contained in the box, a standard NEMA solid faceplate must be installed between the box and the wall station. If fastening into drywall or concrete, use anchors provided. When mounting to wood use a 3/32" drill bit and the drilling template located on page 39. Drill the two 3/32” mounting holes using the drill template. Drill 3/16" holes if using anchors. Install lower screw leaving 7/16" of the screw exposed. Slide wall station keyhole slot onto the lower phillips head screw. Wall station should slide onto screw, providing a snug fit. If necessary remove wall station and loosen or tighten lower phillips head screw until a snug fit is achieved. Once wall station is fitted on lower screw, install upper screw. Do not over-tighten. CAUTION: Over tightening the upper screw could deform plastic case. WARNING Wall Station 5 Foot Minimum Lower Screw Installation Upper Screw Installation 7/16” Keyhole Slot Phillips Head Screw Phillips Head Screw Phillips Head Screw Please Do Not Return This Product To The Store. Call Us Directly! Our Trained Technicians Will Answer Your Questions and/or Ship Any Parts You May Need You can reach us Toll Free at 1-888-827-3667 for Consumer Assistance or online at 8 Press Here To Oper ate Door Battery Cover Up/Down LED Wall Station (2) AAA Batteries Lower Clip 10 Entrapment Warning Label Tools Needed: None Apply entrapment warning label in a convenient location next to the wall station. Use mechanical fasteners if adhesive will not adhere. Service Entrance Door Entrapment Warning Label Wall Station Deluxe Multi-Function Wireless Wall Station Installation Continued (If Included) Remove the battery cover (right-hand side of wall station) by disengaging the battery cover’s lower clip. Install two AAA batteries into the wall station observing the polarity, (+) and (-), of both batteries. After about three seconds, the red LED will begin to blink every three seconds. Re-install the battery cover by first inserting its top into the wall station then inserting and securing its bottom. NOTE: To slow blink rate or turn off, refer to wall station operation page 28 “Back Lit LED Light”. 11 Wired Infrared Safety Sensor Installation Tools Needed: Ratchet Wrench Tape Measure Power Drill 3/16” Drill Bit 7/16” Socket Driver 7/16” Wrench Pencil IMPORTANT: BOTH WALL BRACKETS MUST BE MOUNTED AT THE SAME HEIGHT FOR PROPER ALIGNMENT. Note: Use Steps a-c for installing sensors on both sides of the garage door. a. Select and mark with a pencil, a mounting location no more than 5 inches above the floor to center line of wall mounting bracket. The safety sensors should be mounted as close to the door track or inside edge of the door as possible to offer maximum entrapment protection. It is very important that both wall mounting brackets be mounted at the same height for proper alignment. b. Drill pilot holes, using a 3/16” drill bit. Using two 5/16” x 1-1/2” lag screws, permanently mount the wall mounting brackets to both door jambs. In some installations it may be necessary to attach a wooden spacer to the wall to achieve the required alignment. Attach the “U” brackets to the wall mounting brackets with 1/4”-20 x 1/2” carriage bolts, washers and nuts. Insert the bolts from the inside of the “U” bracket and hand-tighten. IMPORTANT: IDENTIFY WHICH SIDE OF THE GARAG...

Otros modelos de este manual:
La puerta automática - PRODRIVE 3220C (4.85 mb)
La puerta automática - PRODRIVE 3220C-Z (4.85 mb)
La puerta automática - PRODRIVE 3221C (4.85 mb)
La puerta automática - PRODRIVE 3222C (4.85 mb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría