Votos - 1, Puntuación media: 3
(
)
)
|
Resumen del manual
See the drawing on page 5. 2) It is best to mount the video monitor to the roof structure without the mini-console first. There should be a gap between the headliner and the outer flange of the video monitor. The mini-console should be cut to full this gap. Apply masking tape to the outer surface of the mini-console in the areas where the cut will be made. 3) Mark the cut to follow the necessary contour of the roof. The suggested method of marking is as follows: A) First mark the narrowest point of the mini-console on the masking tape. Be careful to consider not only vertical location, but fore-aft location. B) Using the handle of a screwdriver, make a “transfer marking tool”. See diagram below. Place the tool against the roof and the marker against the masking tape on the mini-console. Trace the cut to be made around the entire perimeter of the mini- console. C) Cut the mini-console using a sharp utility knife or shears. Make the cut in several passes over the marked line, each time cutting a little deeper. It is not necessary to cut completely through the plastic, the cut only need be over 50% of the wall thickness of the plastic. By bending the cut back and forth several times, the plastic will break cleanly at the cut. D) Check the fit of the trimmed console and make any minor adjustments necessary. 4) The mini-console can be painted or covered with a material that matches the headliner before assembling the mini-console to video monitor. 5) The finished mini-console should be attached to the video monitor, then attach the assembly to the roof. Tape marker to screwdriver. Starting at your mark for the lowest point, trace the contour of the roof Lowest point mark Cut line Headliner -4 MOUNTING THE MINI-CONSOLE Roof Roof Support Headliner 12”x9”x3/4” Plywood Block (4) Self-Tapping Screws (not supplied) Mini-Console Video Unit (5) #8 Flat Washers (5) #8x3/4” Self-Tapping Screws -5 -6- VOD1023 Figure A 1) Make the connections to the vehicle for the 12 pin wiring harness. 2) Insert the Circular Mini-Din Connector of the source component harness through the wire tie loop on the main PCB and into the Mini-Din Connector on the main PCB. 3) Pull the wire tie loop tight and cut off the excess. 4) Connect the 12 pin harness to the mating connector on the Video Monitor. 5) Connect power harness to vehicle’s electrical system by tapping into an accessory hot line and a good ground. 6) Verify all functions of the System before final mounting of the finished assembly. 7) Mount and connect the Television antenna. (Optional) Note: A VCP or other A/V Component can be connected to the video monitor system using a second source component harness (purchased separately, part number: 8010730). This harness would plug into the Mini-Din connector on the main PCB as in steps 2 and 3 above. A/V Source Definitions: 1= AV1, VCP or VCP with TV Tuner (Mini-Din on main PCB) 2= AUX-IN (VCP, Game or future DVD etc...) 3= Built-in DVD 4= TV (TV Tuner) TV ANTENNA UNIT (BACK VIEW) To TV Antenna In Red RCA (Audio Right) Clean the IR Receiver Window on the front of the VCP. Remove Adhesive Backing and Apply IR LED to IR Yellow RCA (Video) White RCA (Audio Left) "Y" Adapter for use with Non-Stereo Installations Item# 5 Power Connector 4 Pin Accessory Harness - Optional Dome Light (P/N:8010730) Power Source CHOKE Auxillary video display 12 VDC Power and Ground INPUT VIDEO (Yellow) Line Out-R (Red) LINE OUT Patch Cord VIDEO RCA-Female RCA Male to Male Line Out-L (White) Line Out-V (Yellow) To Secondary AV Monitor Power Harness Item #3 Power Harness Item #3 OPTIONAL PODTVT *OPTIONAL RELAY BOX TO OPTIONAL ADDITIONAL MONITOR *ANTENNA FOR WIRELESS FM MOD SIRSWB **See Antenna Note Below *NOTE: If the original relay box P/N SIRSWB is installed, it recommended that the antenna for the wireless FM Modulator be unplugged. See Figure A for antenna location. **NOTE: Extending the wireless antenna beyond its 12 inch length will cause the FM Modulator to exceed FCC limits for wireless transmission. When installing the unit position the antenna for best reception. OPTIONAL CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light. On a positive switched system, with all the doors closed and the lights out, both wires at the dome light will rest at ground. When the light is activated, one of these wires will switch to +12 vdc. This is the vehicle's switching wire. On a negative switched system, with all the doors closed and the lights out, both wires at the dome light will rest at + 12vdc. When the light is activated, one of these wires will switch to ground. This is the switching wire. For positive systems...
Otros modelos de este manual:Vídeo del coche - DVD PLAYER VOD1023 (149.4 kb)
Vídeo del coche - DVD PLAYER VOD1023 S (149.4 kb)