Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
These receivers can be used in a variety of security and remote control applications. When the receiver detects a signal from a transmitter programmed into its memory, the appropriate channel output activates. The channel outputs have three optional configurations; momentary, toggle on/off, and latch until restored. Status and low battery outputs are for supervisory indications. Cutting jumpers select which channels require supervisory status reports from transmitters. Each unit incorporates a dual high-sensitivity superheterodyne diversity receiver with two whip antennas. This type of receiver provides superior performance by preventing loss of signal due to multi-path interference. In a typical installation, the receiver is connected to an alarm control panel, door strike, camera, high current relay or some other devices. Transmitters are used to activate or control the devices. The receiver should be mounted indoors or inside a weather resistant non-metallic housing for outdoor use. The digital DX/DXS code format features over a million possible codes. The transmitters are precoded at the factory to unique codes, so no field coding is required. For versatility, any transmitter can be programmed into any receiver channel. Receivers must be programmed to recognize the transmitter’s code before system testing and operation. Up to 32 transmitters can be programmed into the receiver. Each button on multi-button portable transmitters send a unique code, and are programmed as separate transmitters. The CHANNEL display shows the channels activated and the presence of radio activity. Individual indicators for ALARM, STATUS, and LOW BATT show the supervisory status of each receiver channel. All outputs can be configured for normally open or normally closed. The units can be powered from a 10.2-14.4 VDC or 12-16 VAC power source. The units will draw about 35 mA standby and up to 120 mA in alarm. FEATURES COMPONENT LOCATIONS OPTION JUMPERS AND CHANNEL BUTTONS DETAIL MOUNT RECEIVER ATTACH ANTENNAS CONNECT TERMINALS (760) 438-7000 • FAX (760) 438-7043 USA & Canada (800) 421-1587 & (800) 392-0123 Toll Free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mA MINIMUM OUTPUTS TO DEVICE TO BE TRIGGERED 100 mA MAXIMUM PER OUTPUT WITH OUTPUT POLARITY JUMPER IN PLACE, ALL OUTPUTS WILL SWITCH TO GROUND WHEN ACTIVE NOTE: SEE WIRING EXAMPLES ON REVERSE SIDE OF THESE INSTRUCTIONS WIRING EXAMPLES SELECT OPTIONS ADDING TRANSMITTERS REVIEWING MEMORY REMOVING TRANSMITTERS SYSTEM OPERATION SUPERVISORY CONDITIONS LINEAR LIMITED WARRANTY This Linear product is warranted against defects in material and workmanship for twelve (12) months. The Warranty Expiration Date is labeled on the product. This warranty extends only to wholesale customers who buy direct from Linear or through Linear’s normal distribution channels. Linear does not warrant this product to consumers. Consumers should inquire from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations or liabilities on the part of Linear corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied. All products returned for warranty service ...
Otros modelos de este manual:Vídeo del coche - DXSR-1508 (256.56 kb)