Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
•Do not get the wires under a screw, or caught in moving parts (e.g. seat railing). •Before making connections, turn the car ignition off to avoid short circuits. •Connect the red power input leads only after all other leads have been connected. •Run all ground wires to a common ground point. Fuse replacement When replacing the fuse, be sure to use one matching the amperage rating stated on the original fuse. If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. Fuse (0.5 A) TV aerial amplifier unit 4 Parts list (1) •The numbers in the list are keyed to those in the instructions. • Use 9 and 0 to organize cords. Connection example (2) Connection diagram (3) Installing the TV tuner unit (4) Notes • Ensure that the mounting surface is clean. • Do not install the TV tuner unit – in locations subject to high temperatures. – in locations subject to direct sunlight, warm air from heater outlets, or other locations that can get hot. • When attaching the hook-and-loop fastener to the bottom of the TV tuner unit, do not cover the model name plate in the center. Keep the units and connection cables apart. The AV Center main unit, the monitor, TV tuner unit, and RCA interconnects should not be in close proximity. Otherwise noise interference may affect the TV picture. Mounting the TV aerial Mount the film aerial 5 to the car and connect the TV tuner unit. For directions on connecting the TV tuner unit, see also “Connection diagram (3)”. Before mounting •It may not be possible to mount the aerial on some cars. - In cars with glass that does not transmit radio waves (infrared reflecting glass, insulated glass, glass that is opaque to electromagnetic waves, etc.), the signal reception will be extremely poor. - The aerial cannot be mounted in cars which have airbags in the front pillars. •Mount the aerial to the front window, in the specified location and according to the specified dimensions. - The supplied film aerial is designed for attaching only to the front window. If attached to the rear window or elsewhere in the car, the signal reception may be extremely poor. Notes • Once you have mounted the film aerial, do not attempt to remove it and attach it again, as the adhesive will be considerably weakened. Be sure to temporarily fasten the cable and aerial in place and check that the cable has sufficient play before permanently attaching. • During the mounting procedure, it will be necessary to remove the front pillar molding to attach a ground wire. When performing the installation yourself, if you decide it is too difficult to remove the front pillar molding, please contact your dealer for assistance. (Note that your dealer may charge a fee for their assistance.) Required items Have the following items handy before beginning the mounting procedure. •Tools (Philips screwdriver, etc.) •Cellophane tape •Scissors •Spray bottle (fill with 500 ml water and one or two drops of detergent) •Paper towels Note Mount the film aerials to the inside of the front window. Do not mount the aerials anywhere other than the location described here. Before attaching Using the supplied cleaning cloth qa to wipe away any oil, wax, or dust that may be on the window. Mounting position (5) Installation complete Film aerial mounting procedure Check the film aerial 5 mounting position (6) 1 Align the film aerial power supply point with the lower edge of the window’s ceramic line and fasten temporarily in place with cellophane tape (6-1). Do not remove the adhesive backing from the aerial yet. The figure shows the results of this step, for the left aerial. Temporarily position the right aerial in the same manner. 2 Mark the left and right sides of the film aerial, using cellophane tape, etc (6-2). Remove the inner molding from the front pillars on both sides of the front window (7) The figure shows an example of a car, such as a sedan or SUV, which as a handle mounted on the front pillar. Notes • The molding on the front pillar will be fastened in place with clips or screws. When removing it, take care not to damage or deform it. • When performing the installation yourself, if you decide it is too difficult to remove the front pillar molding, please contact your dealer for assistance. (Note that your dealer may charge a fee for their assistance.) XT-V70 Installation/Connections Установка/Соединения © 2005 Sony Corporation Printed in Japan Notice to dealers and installers Please return this manual to the customer after the installation is completed. Уведомление агентам по продаже и сборщикам После установки аппарата верните это руководство потребителю. Mobile TV Tuner 3 2-597-470-43 (1) Меры предосторожности • Этот аппарат предназначен только для систем с постоянным напряжением в 12 В и заземлением отрицательного полюса. • Не защемляйте провода винтами или движущимися частями (например, направляющими сид...