Votos - 2, Puntuación media: 3.5 ( )

Fabricar: Advantech Tamaño del archivo: 507.36 kb Nombre del archivo: TREK-305Rman.pdf Idioma del manual:

Please refer to Advantech RMA policy Figure 1.3 Backside of TREK-305R TREK-305R User Manual 4 Power button to control LCD backlight On/Off When LCD backlight is on, red LED light is on Figure 1.4 Front side of TREK-305R Pin definition (on TREK) Connector vendor: 3M Touch systems, p/n: 10226-55G3PC Figure 1.5 26-pin connector Pin definition (on VITA) Connector vendor: 3M Touch systems, p/n: 10236-55G3PC Figure 1.6 36-pin connector 5 TREK-305R User Manual Chapter 1 General Information 36 pin CITA-350P Side 26 pin TREK-305R Side 1 LVDS Data0+ 1 LVDS Data0+ 2 LVDS Data0- 2 LVDS Data0- 3 LVDS Data1 + 3 LVDS Data1 + 4 LVDS Data1- 4 LVDS Data1- 5 GND 5 GND 6 T/S signal X+ 6 T/S signal X+ 7 T/S signal Y+ 7 T/S signal Y+ 8 T/S signal X- 8 T/S signal X- 9 T/S signal Y- 9 T/S signal Y- 10 GND 10 GND 11 GPIO 11 GPIO 12 DC +5 V 12 DC +5 V 13 DC +5 V 13 DC +5 V 14 LVDS Data2+ 14 LVDS Data2+ 15 LVDS Data2- 15 LVDS Data2- 16 LVDS Data3+ 16 LVDS Data3+ 17 LVDS Data3- 17 LVDS Data3- 18 LVDS Clock+ 18 LVDS Clock+ 19 LVDS Clock- 19 LVDS Clock- 20 GND 20 GND 21 Line in 21 Line in 22 GPIO 22 GPIO 23 GPIO 23 GPIO 24 GPIO 24 GPIO 25 DC +3.3 V 25 DC +3.3 V 26 DC +3.3 V 26 DC +3.3 V 5 pin DI/DO Side 27 GPIO1 1 GPIO1 28 GPIO2 2 GPIO2 29 GPIO3 3 GPIO3 30 GPIO4 4 GPIO4 31 GND 5 GND 32 X (empty PIN) 33 X (empty PIN) 34 X (empty PIN) 35 X (empty PIN) 36 X (empty PIN) TREK-305R User Manual 6 TREK-305R is design compatible with VITA-350P. Figure 1.7 Front side of VITA-350P 1.4 System Dimensions Figure 1.8 System Dimensions 7 TREK-305R User Manual Chapter 1 General Information TREK-305R User Manual 8 Appendix A LCD Specification A.1 LCD General Specification Item Specifications Display Mode1) TN colors (64 gray scales, 256 k colors) Viewing Direction 6 o’clock (in direction of maximum contrast) Driving Method TFT active matrix CLK (clock), DE (Data Enable signal) H-sync, V-sync (Synchronization signal) R5, R4, R3, R2, R1, R0 (Red display data) G5, G4, G3, G2, G1, G0 (Green display data) B5, B4, B3, B2, B1, B0 (Blue display data) R/L, U/D (Reverse Scan Control) Dimensional Outline2 144.0 (W) x 104.6 (H) x 10.0 max. (D) (mm) Active Area 115.2 (W) x 86.4 (H) (mm) Viewing Area 115.4 (W) x 86.6 (H) (mm) Number of Pixels3) 320 (W) x 240 (H) (mm) Pixel Pitch3 0.36 (W) x 0.36 (H) (mm) Pixel Arrangement3 RGB vertical stripes Surface treatment Anti-glare and hard cost 3H on LCD surface Backlight 18 LEDs (3 rows) for sidelighting Note! 1. k=1024. 2. Excluding backlight cables. 3. Display area address is as follows. TREK-305R User Manual 10 A.2 LCD Optical Specification Item Symbol Conditions Specifications Unit Remark Min. Typ. Max. Viewing Angle 0 CR >=10 = 8 O o 30 50 - o o 0 = 40 70 - o = CD O o 40 70 - o =1 9 O o 40 70 - o Contrast Ratio CR o 0 II -e- o 0 = CD 350 500 - - Response Time tON CD = o o -e- = o o - 15 25 ms O “H “H - 25 35 ms Luminance L 0 =0° 4* =0° Gray Scale Level=163 (White) 255 320 - cd/m2 /f=12 mA Luminance Uniformity LUNF 60 70 - % Chromaticity Red XR Gray Scale Level: L63 0 =0°, =0° 0.52 0.59 0.66 - Yr 0.27 0.34 0.41 - Green XG Ditto 0.29 0.36 0.43 - Yg 0.48 0.55 0.62 - Blue XB Ditto 0.08 0.15 0.22 - Yb 0.05 0.12 0.19 - White XW Ditto 0.25 0.32 0.39 - Yw 0.27 0.34 0.41 - Note! 1. Refer to “11. Measuring Method“. 2. The above test limit must be applied for initial use. Characteristics will be shifted by long period operation, but it is not irregular phenomena. Theoretically brightness characteristics will be decreased due to color shift. 11 TREK-305R User Manual Appendix A LCD Specification TREK-305R User Manual 12 Appendix Touch Panel Specification B.1 Enviroment Specification Chemical Resistance Toluene, Acetone, Methanol, Alcohol, Ethylacetate, Artificial sweat, (top surface) Petroleum ether Condition: Tested after leaving the chemical on the surface for 3 minutes being wiped off by cloth. Judgment: Must be no effect in appearance. B.2 Mechanical Characteristics Operating Life Input (finger) 10,000,000 hits (Note 1) Character Input (pen) 100,000 characters (Note 2) Note! 1. Testing rod (Figure 1), Load 250 g, Cycle 2hit/sec; 2. Testing rod (Figure 2), load 250 g, Input size 10 x 10 mm, Input : character A to Z / minute. These (finger and pen) are tested at same point of the panel surface, and all point will become dis-functin after test. Silicon Rubber (Hardness: 60°) Tip: R = 4.0 Polyacetal resin Tip: R = 0.8 Figure 1 Testing rod 1 Figure 2 Testing rod 2 B.3 Mechanical Characteristics Pressing Force Max 100N (Note 3) Activation Force 0.05N to 1.0N Surface Hardness Over 3H (by JIS pencil hardness) (Note 4) Note! 3. Testing with rubber rod. (0 16 mm, Hardness 60°), Time: 5 s, Center of LCD surface. If you apply pressure over 100N, white spots and da...

Descargar ahora

Introduzca dos números de la imagen: