Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials / Tools required for this installation: 1. Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Awl or scribe point tool or similar 4. Razor knife or similar tool 5. T-10TORX bit driver 6. 1/8" Drill Bit 7. Audiovox Series 640/650 Video Module FOR USE IN VEHICLES WITH FACTORY INSTALLED OVERHEAD CONSOLE ONLY. Materials provided for this installation: Apr. 14, 1999 INSTALLATION INSTRUCTION # 44-0018D Printed in the U.S.A. ITEM DESCRIPTION QTY 1 Nut, 6-32 HH KEPS 8 2 Screw, # 6 x 3/8 PPH TAB 13 3 Screw, # 8 x 9/16 PWH TAB 2 4 Screw, 6-32 x 1/2 PPH 4 5 Screw, 6-32 x 3/4 PPH 10 6 Screw, # 8 x 1 1/4 PWH TAB 2 7 Screw, # 8 x 1 1/2 PWH TAB 1 8 Screw, # 8 x 1 3/4 POH TAB Z1 2 9 Washer, 3.5 mm 4 10 Finish Washer, # 8 2 11 Convoluted Tube, 1/2" ID X 3" 1 12 Template (last page of 1 instructions) 13 Front Mounting Bracket 1 14 Pod Mounting Bracket 4 15 Switch Mounting Bracket 2 16 Rear Air Duct Blockoff Plate 1 17 Rear Mounting Bracket 1 18 Plywood , 3/8" x 7" x 8 1/2" 1 19 Overhead Console 1 INSTALLATION INSTRUCTION # 44-0018D Apr. 14, 1999 Printed in the U.S.A. 2 3 I. REMOVAL OF O.E.M. EQUIPMENT. 1. Remove and retain OEM overhead console assembly by removing one (1) OEM screw in front pocket. Pull console down and disconnect wiring. Set aside in a safe place for later re-installation. 2. Remove and retain rear A/C control assembly. Assembly housing is secured with two (2) spring loaded fasteners on front of housing. Pull down to disengage, then slide forward to clear bracket. Disconnect wiring. Set assembly aside in a safe place for re-use later. 3. Remove center A/C vent in headliner using two scribe points in indicator holes on vent and twist. II. PREPARATION OF VEHICLE. 1. Place template provided (item 12 pg 2) over center A/C vent hole with arrow pointing forward. Cut and remove indicated headliner. See Figure 1. 2. Install plywood block (item 18 pg 2) provided in kit through modified louver opening and secure in place using two (2) # 8 x 9/16" PWH screws (item 3 pg2). See Figure 2 and 3. Figure 1 Figure 2 Figure 3 4 Figure 4 4. Detach wire harness from brace where A/C assembly was removed. Remove and retain two (2) OEM screws. Trim headliner to clear front flange of rear mounting bracket (item 17 pg 2) Insert rear mounting bracket tabs in existing slots on rear of OEM brace. Align holes of bracket with OEM bracket. Secure with OEM screws. See Figure 5. Route wiring toward driver’s side of bracket. Install convoluted tube (item 11 pg 2) around wire harness to prevent chaffing against bracket. Figure 6 3. Install block-off cover (item 16 pg 2) using one (1) # 8 x 1 1/4" PWH screw (item 6 pg 2). See Fig. 4. (Use caution to assure screw does not penetrate vehicle roof ). Figure 5 5. Remove and retain two (2...
Otros modelos de este manual:Vídeo del coche - 1181280 (1.54 mb)
Vídeo del coche - 1181281 (1.54 mb)
Vídeo del coche - 1181281 (1.54 mb)