Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
If this happens, return the handset to the base for about 5 seconds. This resets the security access-protection code. • About once a month, fully discharge the battery pack by keeping the handset off the base until the BATT LOW indicator lights. Otherwise, the battery pack loses its ability to fully recharge. • If the BATT LOW indicator does not light, but the phone does not work, recharge the battery pack. (The battery pack charge might be too low to light the indicator.) • If the battery pack becomes weak during a call, you hear a beep and the BATT LOW indicator flashes. End the call as soon as conveniently possible, and recharge the battery pack before using the phone again. • If the battery pack is completely discharged or the base loses power while the handset is away from it, place the handset on the base to reset the security access-protection code. If it was the handset that lost power, recharge the battery pack. • The supplied battery pack should last for about a year. When the battery pack loses its ability to fully recharge, order a replacement battery pack from your local RadioShack store (see “Replacing the Battery Pack” on Page 32). SETTING THE DIALING MODE Set T/P (Tone/Pulse) on the back of the base for the type of service you have. If you are not sure which type you have, after you charge the handset battery pack, do this simple test. 1. Set T/P to T. 2. Press TALK on the handset and listen for the dial tone. 3. Press any number other than 0. Note: If your phone system requires that you dial an access code (9, for example) before you dial an outside number, do not press the access code either. If the dial tone stops, you have touch-tone service. Leave T/P set to T. If the dial tone continues, you have pulse service. Set T/P to P. 4. Press TALK on the handset or place the handset on the base to hang up. 14 43-789.fm Page 15 Monday, August 16, 1999 8:32 AM TURNING THE RINGERS OFF OR ON To turn off the ringers on the base and handset, set RINGER on the right side of the base to OFF. You can still make or receive calls using this phone, and telephones on the same line still ring when there is an incoming call. The IN USE indicator on the base and the TALK indicator on the handset will flash until you answer the call. To turn on the base and handset ringers, set RINGER to ON. SETTING THE NUMBER OF RINGS Set the 2/4/TS switch on the back of the base to 2, 4, or TS to select how long the TAD waits before it answers a call (2 rings, 4 rings, or toll-saver). Note: If you plan to check your messages by long distance, set the number of rings to toll-saver (see “Using Toll- Saver” on Page 28). SETTING THE DAY AND TIME You must set the day of the week and time so the TAD can record the correct day and time of each message. Note: To avoid losing the day and time settings if AC power is lost, we recommend you install backup batteries before you set the day and time (see “Installing Backup Batteries” on Page 12). With the Handset 1. Press REMOTE. The REMOTE indicator lights. REMOTE Indicator ) then CLOCK (8). The TAD announces the currently set day. 2. Press CHANGE ( 15 43-789.fm Page 16 Monday, August 16, 1999 8:32 AM 3. To change the day, repeatedly press SKIP (6) to move forward or REPEAT (4) to move backward. 4. Press CLOCK. The TAD announces the hour and “AM” or “PM.” 5. To change the hour, repeatedly press SKIP or REPEAT. 6. Press CLOCK. The TAD announces the minutes. 7. To change the minutes, repeatedly press SKIP or REPEAT. 8. When you finish, press CLOCK. The TAD announces the day and time and beeps twice. 9. Press REMOTE. The REMOTE indicator turns off. With the Base 1. Hold down CLOCK until the TAD announces the currently set day. 2. To change the day of the week, repeatedly press SKIP( ) to move forward or REPEAT( ) to move backward. 3. Press CLOCK. The TAD announces the hour and “AM” or “PM.” 4. To change the hour, repeatedly press SKIP or REPEAT. 5. Press CLOCK. The TAD announces the minutes. 6. To change the minutes, repeatedly press SKIP or REPEAT. 7. When you finish, press CLOCK. The TAD announces the day and time. 16 43-789.fm Page 17 Monday, August 16, 1999 8:32 AM TELEPHONE OPERATION MAKING AND RECEIVING A CALL To make a call, lift the handset and press TALK. When you hear the dial tone, dial the desired phone number or memory number (see “Memory Dialing” on Page 19). To answer a call if the handset is on the base, simply lift the handset and begin your conversation. If the handset is away from the base, press TALK. The TALK indicator on the handset and the IN USE indicator on the base light. TALK Indicator To end a call, press TALK on the handset or place the handset on the base. The TALK and the IN USE indicators turn off. Note: If you press TALK to hang up and the phone does not disconnect, place the handset on the base. SETTING THE HANDSET’S VOLUME You can change the handset’s volume during a call by repeatedly pressing VOLUME. The volume steps up and down the three settings (low, m...