Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
If your telephone wiring does not have a modular jack, you can update it yourself using jacks and adapters available at your local RadioShack store, or have the telephone company update it for you. • The USOC number of the jack to be installed is RJ11C (or RJ11W for a wall plate jack). Caution: The supplied AC adapter was designed specifically for your TAD-759. Use only the supplied adapter. On a Desk Top 1. Plug one end of the supplied long modular cord into the TEL. LINE jack on the back of the base. TEL. LINE Jack 2. Plug the cord’s other end into a modular phone line jack. 3. Plug one end of the supplied coiled handset cord into the jack at the left side of the base. Plug the other end into the handset’s jack. TAD as shown. 4. Place the handset on the base. 5. Insert the supplied AC adapter’s barrel plug into the AC 9V jack on the back of the base. AC 9V Jack 6. Plug the adapter into a standard AC outlet. When you first connect power, flashes on the message counter as the TAD runs a self-test. The TAD beeps and 00 appears when the test is complete. On a Wall Plate or Wall Note: To mount the base directly on the wall, you need two screws (not supplied) with heads that fit into the keyhole slots on the bottom of the base. Drill two holes 315/16 inches (100 mm) apart. Then thread a screw into each hole, letting the heads extend about 3/16 inch (5 mm) from the wall. 1. Snap the supplied mounting bracket into the slots on the bottom of the Note: Be sure the keyhole slots on the bracket and the TAD are aligned in the same direction. 2. Plug one end of the supplied short modular line cord into the TEL. LINE jack on the back of the TAD. TEL. LINE Jack 8 3. Insert the supplied AC adapter’s barrel plug into the AC 9V jack on the back of the base. 4. To mount the phone on a wall plate, plug the other end of the modular cord into the wall plate jack. Then, with the power cord hanging over the bracket, align the TAD’s keyhole slots with the wall plate studs and slide the TAD downward to secure it. To mount the phone directly on a wall, with the power cord and the modular cord hanging over the bracket, align the TAD’s keyhole slots with the screws and slide the TAD downward to secure it. 5. Slide the handset clip out of its retaining slot, rotate it 180°, then slide it back into its slot. 6. Plug one end of the supplied coiled handset cord into the jack at the left side of the base. Plug the other end into the handset’s jack. 7. Place the handset on the base. 8. Plug the adapter into a standard AC outlet. When you first connect power, _ _ flashes on the message counter as the TAD runs a self-test. The TAD beeps and 00 appears when the test is complete. SETTING THE DIALING MODE Set PULSE/TONE for the type of service you have. If you are not sure which type you have, follow these steps. AC 9V Jack 1. Set PULSE/TONE on the back of the TAD to TONE. 2. Lift the handset and listen for a dial tone. 3. Press any number except 0. Note: If your phone system requires that you dial an access code (9, for example) before you dial an outside number, do not dial the access code either. If the dial tone stops, you have touch- tone service. Leave PULSE/TONE set to TONE. If the dial tone continues, you have pulse service. Set PULSE/TONE to PULSE. SETTING THE DAY AND TIME The TAD-759 records the day and time each memo and message is recorded. Follow these steps to set the day and time. Note: If you do not complete each step within 8 seconds, the TAD sounds three beeps and exits. Start again at Step 1. 1. Hold down SET until the TAD beeps. The TAD announces, “Sunday,” and 01 appears on the display. Note: If necessary, adjust VOLUME on the right side of the TAD to the desired listening level. 2. To change the day, repeatedly press SKIP to move backward or REPEAT to move forward until the TAD announces the desired day. 3. Press STOP. The TAD shows the cur- rently set hour and announces “AM” or “PM.” 4. To change the hour, repeatedly press SKIP or REPEAT. 5. Press STOP. The TAD shows the currently set minute. 6. To change the minutes, repeatedly press SKIP or REPEAT. 7. Press STOP. The TAD announces the day and time. To check the current day and time at any time, press SET. SETTING THE NUMBER OF RINGS Set the ring select switch on the back of the TAD to 4, 7, or TS to set how long the TAD waits before it answers a call (4 rings, 7 rings, or toll-saver). If you plan to check your messages by long distance, set the ring select switch to TS (see “Using Toll-Saver” on Page 18). TELEPHONE OPERATION Place and answer phone calls with the TAD-759 as you would with any standard phone. SETTING THE RINGER’S VOLUME To change the ringer’s volume, set the ringer volume switch on the back of the base to LO for a normal ringer volume, or HI for a louder ring. If you do not want the ringer to sound, set the ringer volume switch to OFF. You can still make calls with the ringer off, and you can answer calls if you hear another phone on the same line ring. US...