Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
43-777.fm Page 9 Friday, August 13, 1999 3:44 PM ANSWERING SYSTEM OPERATION SETTING THE TAD-277 TO ANSWER CALLS Rotate VOLUME to the right until it clicks to turn on the TAD-277. When the message indicator stays on and the TAD-277 does not sound any tones, it is ready to answer calls. The TAD-277 hangs up and resets to answer the next call when: • The caller hangs up. • The maximum message length of about 1 minute or 5 minutes is reached (see “Setting the Maximum Message Length” on Page 8). • There are more than 7 seconds of silence. The TAD-277’s supplied tape can record up to about 29 minutes of incoming messages per side. You can buy additional and different length cassettes at your local RadioShack store. If the tape reaches the end while a caller is leaving a message, the TAD277 beeps twice and hangs up. If the incoming message tape is full, the TAD-277 answers a call after ten rings, plays back the outgoing mes sage, then waits 7 seconds for you to enter the remote operation security code. If you do not enter the correct code, the TAD-277 beeps twice and hangs up. See “Remote Control Operation” on Page 11. To have the TAD-277 not answer calls, turn it off by rotating VOLUME to the left until it clicks. The message indicator turns off. SETTING THE SYSTEM’S VOLUME To adjust the volume, set VOLUME to a comfortable listening level. (This does not affect the volume of the message the caller hears.) SCREENING CALLS To screen calls, let the TAD-277 answer them. Listen to the caller’s message through the TAD-277’s speaker. If you decide to answer the call, pick up any phone on the same phone line as the TAD-277. The TAD-277 stops recording and resets to answer the next call. 9 43-777.fm Page 10 Friday, August 13, 1999 3:44 PM Note: If you pick up the phone just as the TAD-277 answers, the TAD-277 might not stop recording the message. If this happens, briefly hang up the phone then pick it up again. PLAYING MESSAGES When you have messages, the message indicator blinks. If you have four messages or less, the light blinks once for each message stored. (For example, if you have two messages, the light blinks twice followed by a 2-second pause, then blinks twice more, and so on.) If you have more than four messages, the light blinks continuously. Note: The light also blinks continuously if the TAD-277 receives one or more incoming messages after power is interrupted (see “Troubleshooting” on Page 13). To play the messages, press PLAY. The TAD-277 beeps once, rewinds the tape, then plays the messages. Notes: • To pause playback, press PLAY. To restart playback, press PLAY again. 10 If you do not restart playback within 60 seconds, the tape fast- forwards to the end of the last incoming message, as though playback was never started. This helps prevent accidental erasure of incoming messages. • If a call comes in while playback is paused, the tape immediately fast-forwards to the end of the last message and answers the call. After you play back all the messages, the TAD-277 beeps twice, rewinds to the beginning, and resets to answer calls. New messages will be recorded over the messages you have heard. To save the messages, press SAVE before a new call is recorded. The tape fast-forwards to the end of all the messages and resets to answer calls. To replay the messages, simply press PLAY again. 43-777.fm Page 11 Friday, August 13, 1999 3:44 PM REMOTE CONTROL OPERATION While you are away from your home or office, you can use a touch-tone phone or a pulse phone with a pocket tone dialer to: • Set the TAD-277 to answer calls • Play your messages • Record a message • Set the TAD-277 to record over old messages REMOTE ANSWER-ON You can use a remote phone to set the TAD-277 to answer calls if: • The TAD-277 has power. • The cassette is loaded. • The TAD-277 is off. To remotely set the TAD-277 to answer calls, dial your phone number then let your phone ring at least 12 times until the TAD-277 answers. Then hang up the phone. Notes: • Your phone rings 10 times plus the number of rings you have set using RING SELECT (see “Setting the Number of Rings” on Page 8) before the TAD-277 answers. For example, if RING SELECT is set to 7, the TAD-277 answers after 17 rings. • When you return, be sure to rotate VOLUME to turn the TAD-277 on. Then you can play any messages you received while you were gone (see “Playing Messages” on Page 10). REMOTE PLAYBACK You must know your 3-digit remote operation security code to play back or record messages from a remote phone. The code for your particular answering system is printed on the bottom of your TAD-277. To play back yourmessagesfrom a remote phone, dial your phone number. After the TAD-277 plays the outgoing message and beeps, enter the remote operation security code within 7 seconds. (Be sure each button press is at least 1/2 second long). The TAD-277 sounds a tone while the tape rewinds. If no tone sounds, re-enter the code. Notes: • If you do not enter the code within 7 seconds, the TAD...