Votos - 2, Puntuación media: 4.5 ( )

Fabricar: Panasonic Tamaño del archivo: 2.11 mb Nombre del archivo: Idioma del manual:

3 Insert the hooks on the wall mounting adaptor into the holes 1 and 2 on the base unit. 4 Adjust the adaptor to hold the base unit, then push it in the direction of the arrow until it clicks into place. Hook AC adaptor cord 1 2 2 1 Useful Information For assistance, please visit 37 5 Connect the telephone line cord. Mount the unit by inserting the mounting pins into the round openings on the adaptor (for pin 2, use round cut out at the bottom of the adaptor if you are using the 4 inches phone plate), then sliding the unit down to secure it. Connect the AC adaptor to power outlet (page 9). LThere are two common types of wall phone plates. The distance between 1 and 2 may vary depending on the size of the wall phone plate installed. To remove the wall mounting adaptor While pushing down the release levers (A), remove the adaptor (B). Belt clip You can hang the handset on your belt or pocket using the included belt clip. To attach the belt clip To remove the belt clip While pressing the top of the clip(A), pull the right edge in the direction of the arrow (B). 83 mm (31/4 inches) 102 mm (4 inches) 2 1 83 mm (31/4 inches) or 102 mm (4 inches) 1 (120 V AC, 60 Hz) 2 B A A A B Useful Information Headset (optional) Connecting a headset to the handset allows hands-free phone conversations. We recommend using the Panasonic headset noted on page 5. LHeadset shown is KX-TCA86. For assistance, please visit Useful Information Error messages If the unit detects a problem, one of the following messages is shown on the display. Display message Cause/solution Busy LThe called handset is in use. LThe handset you are calling is too far from the base unit. LThere is no handset registered to the base unit matching the extension number you entered. LOther units are in use and the system is busy. Try again later. Error!! LRecording was too short. Try again. Failed LThe handset you tried to copy phonebook items to is in use. Try again later. Incomplete LThe destination handset’s phonebook memory is full. Erase unnecessary items from the destination handset’s phonebook (page 19). Memory full LThere is no space to store new items in the phonebook. Erase unnecessary items (page 19). Messages full LThere is no space in memory to record new messages. Erase unnecessary messages (page 28). No items stored LYour phonebook, caller list or redial list is empty. No link to base. Move closer to base, try again. LThe handset has lost communication with the base unit. Move closer to the base unit, and try again. LConfirm that the base unit’s AC adaptor is plugged in. LThe handset’s registration may have been canceled. Re-register the handset (page 35). Please lift up and try again. LA handset button was pressed while the handset was on the base unit or charger. Lift the handset and press the button again. Please set current date & time. LIn order to set the alarm, you must first set the date and time (page 15). For assistance, please visit Useful Information Troubleshooting General use Problem Cause/solution The unit does not work. LMake sure the batteries are installed correctly and fully charged (page 10). LCheck the connections (page 9). LUnplug the base unit’s AC adaptor to reset the unit. Reconnect the adaptor and try again. LThe handset has not been registered to the base unit. Register the handset (page 35). I cannot hear a dial tone. LConfirm the telephone line cord is properly connected (page 9). LDisconnect the unit from the telephone line and connect a known working telephone. If the working telephone operates properly, contact our service personnel to have the unit repaired. If the working telephone does not operate properly, contact your telephone service provider. The indicator on the top LNew messages have been recorded. Listen to right of the handset flashes the new messages (page 28). slowly. LNew Voice Mail messages have been recorded. Listen to the new Voice Mail messages (page 33). Programmable settings Problem Cause/solution I cannot program items. LProgramming is not possible while either the base unit or another handset is being used. Try again later. While programming, the handset starts to ring. LA call is being received. Answer the call and start again after hanging up. For assistance, please visit Useful Information Battery recharge Problem Cause/solution I fully charged the batteries, but 7 continues to flash. LClean the charge contacts and charge again (page 11). LThe batteries may need to be replaced with a new ones (page 10). I fully charged the batteries, but the operating time seems to be short. LWipe the battery ends (S, T) and the unit contacts with a dry cloth. The handset display is blank. LConfirm that the batteries are properly installed. LFully charge the batteries (page 10, 11). Making/answering calls, intercom Problem Cause/solution w is displayed, but I cannot make a call. LThe handse...

Descargar ahora

Introduzca dos números de la imagen: