Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
See Caller ID Operation, beginning on page 23, for more details about how these features work. Telephone operating range This cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC). Even so, this handset and base can communicate over only a certain distance — which can vary with the locations of the base and handset, the weather, and the construction of your home or office. For best performance, keep the base antenna fully upright. If you receive a call while you are out of range, the handset might not ring — or if it does ring, the call might not connect when you press PHONE. Move closer to the base, then press PHONE to answer the call. If you move out of range during a phone conversation, you might hear noise or interference. To improve reception, move closer to the base. If you move out of range without pressing O, your phone will be left “off the hook.” To hang up properly, walk back toward the telephone base, periodically pressing Ountil the call is disconnected. 5 91-005677-031-000.ATT1477.RO.qxd 2/13/1950 7:21 PM Page 6 Getting Started Telephone base installation Install the speakerphone base as shown below. Choose a location away from electronic equipment, such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture. NOTE: Use only the power cord supplied with this product. If you need a replacement, call 1-800-222-3111. Plug telephone line cord Plug power cord Be sure to use an electrical outlet into telephone jack. transformer into not controlled by a wall switch. electrical outlet. 6 91-005677-031-000.ATT1477.RO.qxd 2/13/1950 7:21 PM Page 7 Getting Started Battery installation & charging After installation, place the handset in the base and allow the battery to charge for 12 hours before use. You can keep the battery charged by returning the handset to the base after each use. When battery power is fully depleted, a full recharge takes about 8 hours. Press coin into slot on base of handset to release latch, then remove cover. Place handset in base to charge for 12 hours before first use. Rotate antenna to fully upright position. Low battery indicator Return handset to base to recharge when this symbol appears. (Handset will beep when battery is low.) Charging light will be illuminated while battery is charging. Plug in battery here. BATTERY LOW 8/12 10:06 AM Insert top tabs first. Press down to click in place. 7 91-005677-031-000.ATT1477.RO.qxd 2/13/1950 7:21 PM Page 8 Getting Started Wall mounting The speakerphone base can be installed on any standard wall-phone outlet as shown below. Choose a location away from electronic equipment, such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture. Swivel wall mount down Connect line cord and AC adapter as and lock in place. shown on page 6, then grasp and Plug power cord transformer into electrical outlet. Plug telephone line cord into telephone jack. squeeze to open hinged wall mount. Press and slide down firmly so base is held securely on outlet mounting pegs. 8 91-005677-031-000.ATT1477.RO.qxd 2/13/1950 7:21 PM Page 9 Getting Started Belt clip & optional headset Install belt clip as shown below if desired. For hands-free telephone conversations, you can use any industry standard 2.5 mm headset (purchased separately). For best results use an AT&T 2.5 mm headset. Snap belt clip into notches on side of handset. Rotate and pull to remove. Plug 2.5 mm headset into jack on side of handset (beneath small rubber cap). 9 91-005677-031-000.ATT1477.RO.qxd 2/13/1950 7:21 PM Page 10 Press @PROG/CHAN to begin programming Press V or ^to display features one by one Press SELECT to modify a displayed feature Telephone Operation Customizing your telephone Follow the steps below to program the telephone. To stop at any time, press O. If the phone rings, programming stops automatically so you may answer the call. Choose ringer sound (see note on next page) 1 Press @PROG/CHAN to begin programming. 2 Press ^ until screen displays RINGER & setting. 3 Press SELECT to change current setting: RINGER: 1 Default setting: 1 4 Press ^to display 1, 2, 3, 4, or OFF. You will hear a sample of each ringing type. 5 Press SELECT to select displayed ringing type and exit. Set date and time To stop at any time, press O 1 Press @PROG/CHAN to begin programming. 2 Press ^until screen displays DATE/TIME. 3 Press SELECT to view or change date and time: DATE/TIME Default setting: 1/01 12:00 AM 1/01 12:00 AM 4 Press V or ^to change month, then press SELECT. 5 Repeat Step 4 to set day, hour, minute, and AM/PM. 6 Press SELECT to save selection and exit. NOTE: You can choose to set the time manually, or you can allow it to be set automatically with incoming Caller ID information. The time will be set automatically only if you subscribe to Caller ID service provided by your local telephone company (see page 5). 10 91-005677-031-000.ATT1477.RO.qxd 2/...