Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
LINE 1 is selected. Rotate [JOG DIAL I until the caller you want to clear is displayed. Press ICLEARl. • A long beep sounds and the information is erased. • In a few seconds, the display will show the previous caller information. • To return to the stand-by mode, press (EXIT] or wait for 60 seconds. New calls 10 LXNEl TOM REAGAN 444-5555 3 : 10P JUN LINEl 10 C 1 e a r ICALLERID) ŒZD Display [JOG DIALl 36 To clear all of the entries on the desired line(s) in the Caller List Press [CALLER ID] to enter the list. New calls •“CALLER ID key=Select line 0 12 LINEl LINE2 JOG=Listing” is displayed, then the number of new calls on both lines will be shown. a) To clear callers on both lines, go to step 3. b) To clear callers on either line, press Ex. LINE 1 is selected. [CALLER ID] repeatedlv to select the line. New calls 0 LINEl Press [CLEAR], LINEl All clear ? * =Y OS # =No Press (*) (Yes key). LINEl All clear • A long beep sounds and all of the entries for The display will return to the stand-by mode. You can also clear all of the entries by setting the display to “End of new calls”, "End of old calls” or “End” by rotating IJQG dial I after selecting the line in step 2. 37 Advanced Operation Voice Mail Service Voice mail service is an electronic on-line answering system offered by your telephone company. After you subscribe, the voice mail system can answer calls automatically when the line is busy or if calls are not answered. Callers can leave messages by following the pre-recorded instructions. When voice mail messages are recorded, the IVOICE MAILI button will flash. You can access the voice mail system quickly by using the [VOICE MAILl button. To use the [VOICE MAILl button, you must store your access phone number for the line first. Line Buttons Display IVOICE MAlP ISP-PH ON E/HEADS ET 1 I JOG DIAL] 38 Storing an Access Number in Your Voice Mail Be sure that the handset is on the cradle, the AC adaptor is connected and the SP-PHONE/HEADSET indicator light is off. H Press [FUNCTION/EDIT). ^Date and time Area code 2nd area code — Function list- p Rotate I JOG DIALl until “Voice mail #” ¡S ^ selected. • The arrow points to “Voice mail #”. 2 Press ISEND/SETI. 4 5 Rotate I JOG DIALl to select the desired line, “Linel” Or “Line2”. Press ISEND/SETI (Next key). • “Enter v.m. #” is displayed. • The current set number is displayed, if it was stored beforehand. 6 Enter your access phone number up to 32 digits. • If you misdiai, press (clear). Digits are erased from the right. y Press [SEND/SETI (Save key). • A long beep sounds and the number is saved. • The display will return to the function list. To program the other line, start from step 3. • To return to the stand-by mode, press I EXIT] or wait for 60 seconds. 2nd area code -»Voice mail # Voice mail tone -Func Cion lisc- Voice mail # ,\ :Linell vH S ET = Next Voice mai^ ^ :Line2 SET=NexC Enter V.M. # > □ SET=Save 12-345-67 890 S ET=Save 12-345-6789 * * * Saved. * * * • You can exit the programming mode any time by pressing I EXIT]. 39 Advanced Operation Voice Mail Service Setting the Voice Mail Tone If your voice mail service sends a voice mail tone after a new message has finished recording, set to “On”. The IVOICE MAIL! button will flash if a message was recorded in your mailbox. You will hear a series of voice mail tones then a dial tone after lifting the handset or pressing ISP-PHONE/HEAPSET). (Contact your service provider about your service.) Set to “Off’ when: — you do not subscribe to a voice mail service, — your voice mail service does not send a voice mail tone, or — the unit is connected to a PBX. Your phone comes from the factory set to “On”. Be sure that the handset is on the cradle, the AC adaptor is connected and the SP-PHONE/HEADSET indicator light is off. 1 Press [FUNCTION/EDITl. -»Date and time Area code 2nd area code —Function list — p Rotate IJOG DIAL] until “Voice mail ^ tone” is selected. • The arrow points to “Voice mail tone”. 0 Press [SEND/SEp. Voice mail # -*Voice mail tone Line selection -Function list- Voice mai}, tonej : Linelj S et = Next Rotate [JOG DIAL] to select the desired line, “Linel” or “Line2”. Voice mail«. tone/( :Line2 S ET = Next ^ Press ISEND/SET1 (Next key). • The current setting, “on” (factory preset) or “off”, is displayed. O Rotate [JOG dial I until the desired setting is displayed. Voice mail ^oge Line2: On \' S ET = Save Voice mail^ton& Line2: Of f S ET = Scive y Press [SEND/SETI (Save key). • A long beep sounds and the setting is saved. Voice mail tone Line2: 0 f £ The display will return to the function list. To program the other line, start from step 3. To return to the stand-by mode, press I EXIT] or wait for 60 seconds. 40 • You can exit the programming mode any time by pressing [EXITI. Listening to Voice Mail Message(s) Up to 4 minutes after receiving a voice mail message...