Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
Ground (10.5-16V) 6 7 maximum current draw dimensions (W x H x L) mm inches 2-4 Ohms 15A 4-8 Ohms input impedance low level inputs high level inputs 10K Ohms 100 Ohms matching speaker impedance stereo mode bridged mode f e a t u r e s a n d c o n t r o l s 2 c h a m p P L A 2 1 7 0 . P L A 2 2 7 0 f e a t u r e s a n d s p e c i f i c a t i o n s 2 c h a m p P L A 2 1 7 0 . P L A 2 2 7 0 292 x 60 x 209 11.5 x 2.34 x 8.25 P L A 2 2 7 0 2 channel amplifier 75 Watts x 2 110 Watts x 2 500 Watts x 2 20A 292 x 60 x 305 11.5 x 2.34 x 12 crossover mode selector input level control bass boost level low pass frequency control high pass frequency control protection LED power LED high level inputs low level inputs speaker connections power terminals power fuse remote bass boost (PLA2170 without) crossover mode selector input level control low pass frequency control high pass frequency control Remote Bass Boost bass boost level control low level inputs high level inputs power LED protection LED power fuse power terminals speaker connections when used with normal, full range systems, set this switch to “FULL.” If you wish to use the internal crossover to power a driver of specific frequency range, use the “LOWPASS” or “HIGHPASS” settings. use this control to match the outputs of your head unit to the amplifier. Starting with your head unit set at about the 2 o’clock position, increase the amp level control until distortion begins to occur, and reduce slightly from this point. when the crossover selector switch is in “low pass” mode, this control sets the upper frequency limit for audio program sent to the speakers. when the crossover selector switch is in “high pass” mode, this control sets the lower frequency limit for audio program sent to the speakers. Plug in the Remote Bass Boost Control wire in here. this control permits adjustment of the bass level up to an increase of approximately 18 dB. this amp features gold-plated RCA input jacks for high impedance input. Use these with car stereo output which uses RCA-type connector cables. if your car stereo lacks RCA-type output jacks, you may connect speaker output leads to these input connectors. this indicator is illuminated when power is applied. this indicator is illuminated when built-in protection circuitry is activated. the fuse protects the amplifier and your car’s electrical system from short circuit conditions. use these connectors to deliver power, ground and remote turn-on control to the amplifier. these terminals are 14K gold plated to guarantee high conductivity and minimum signal loss. P L A 2 1 7 0 P L A 2 2 7 0 8 9 f e a t u r e s a n d c o n t r o l s 2 c h a m p P L A 2 3 7 0 . P L A 2 4 7 0 f e a t u r e s a n d s p e c i f i c a t i o n s 2 c h a m p P L A 2 3 7 0 . P L A 2 4 7 0 P L A 2 3 7 0 2 channel amplifier frequency response power supply voltage output power @ 14.4v DC, 1KHz RMS Power @ 4 Ohms RMS Power @ 2 Ohms Maximum Power Output input sensitivity low level inputs high level inputs 100 Watts x 2 150 Watts x 2 700 Watts x 2 15 Hz-30 KHz 250mV 2.5V 14.4V DC Neg. Ground (10.5-16V) maximum current draw dimensions (W x H x L) mm inches 2-4 Ohms 30A 4-8 Ohms input impedance low level inputs high level inputs 10K Ohms 100 Ohms matching speaker impedance stereo mode bridged mode 292 x 60 x 400 11.5 x 2.34 x 15.75 P L A 2 4 7 0 2 channel amplifier 150 Watts x 2 220 Watts x 2 800 Watts x 2 50A 292 x 60 x 432 11.5 x 2.34 x 17 speaker connections power termi...