Iniciar sesión:
Votos - 2, Puntuación media: 4 ( )

Manual de usuario Lanzar Car Audio, modelo HERITAGE HTG 264

Fabricar: Lanzar Car Audio
Tamaño del archivo: 487.48 kb
Nombre del archivo:
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Attach all audio system components securely within the automobile to prevent damage, especially in an accident. 3. Do not mount this amplifier so that the wire connections are unprotected or in a pinched condition, or likely to be damaged by nearby objects. Be sure to select a location inside your vehicle which has adequate ventilation. 4. Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminais. 5. If you need to replace the power fuse, only replace it with a fuse identical to that supplied with the system. Using a fuse fo a different type or rating may result in damage to your system which isn’t covered by the manufacturer’s warranty. System Wiring 2 Channel Stereo Configuration HTG 214/ 224/ 234/ 244/ 254/ 264 FRONT To OUTPUT from HEAD UNIT To REMOTE Subwoofer level control 8 System Wiring 2 Channel Bridged Mode Configuration HTG 214/ 224/ 234/ 244/ 254/ 264 FRONT To REMOTE Subwoofer level control HEAD UNIT To OUTPUT 9 System Wiring 2 Channel Tri-Mode Configuration HTG 214/ 224/ 234/ 244/ 254/ 264 FRONT REAR To REMOTE Subwoofer level control To OUTPUT from HEAD UNIT HTG 244/254/264 To BATTERY®- To REMOTE OUTPUT- From HEAD UNIT Speaker Impedance 4-8 Ohm 10 Tri-Amp System Using Three 2 Channel Amplifiers System Wiring HTG 214/224/234/244/254/264 11 System Wiring 4 Channel Stereo Configuration HTG 414/424/434 FRONT To BATTERY® To REMOTE OUTPUT- From HEAD UNIT Speaker Impedance 2-4 Ohm REAR To REMOTE Subwoofer level control YADAPTOR YADAPTOR To OUTPUTfrom HEAD UNIT 12 System Wiring 4 Channel Bridged Mode Configuration HTG 414/424/434 FRONT REAR YADAPTOR To LEFT OUTPUT From HEAD UNIT YADAPTOR To REMOTE Subwoofer level control To RIGHT OUTPUT From HEAD UNIT To REMOTE OUTPUT From HEAD UNIT Speaker Impedance 4-8 Ohm To BATTERY® 13 System Wiring 4 Channel Tri-Mode Configuration HTG 414/424/434 FRONT 14 YADAPTOR YADAPTOR To REMOTE Subwoofer level control To OUTPUTfrom HEAD UNIT REAR To BATTERY® To REMOTE OUTPUT- From HEAD UNIT Speaker Impedance 4-8 Ohm Right flcmot« O PUW. O wot Uval & Troubleshooting Troubleshooting Amplifier will not power up. • Check for good ground connection. • Check that remote DC terminal has at least 3V DC. • Check that there is battery power on the + terminal. • Check all fuses. • Check that Protection LED is not lit. If it is lit, shut off amplifier briefly and then repower it. High hiss orengine noise (alternator whine) in speakers. Disconnect all RCA inputs to the amplifier(s)-if hiss/noise disappears, then plug in the component driving the amplifier and unplug it's inputs. If hiss/noise • disappears, go on until the faulty/noisy component is found. It is best to set the amplifier's input level as low as possible. The best subjective S/N ratio is obtainable this way. Try to drive ...

Otros modelos de este manual:
Avtousiliteli - HERITAGE HTG 214 (487.48 kb)
Avtousiliteli - HERITAGE HTG 224 (487.48 kb)
Avtousiliteli - HERITAGE HTG 234 (487.48 kb)
Avtousiliteli - HERITAGE HTG 244 (487.48 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría