Votos - 3, Puntuación media: 3
(
)
)
|
Resumen del manual
Features and controls 8.9.10. System wiring 11.12. Troubleshooting jCanzar Vibe Owner's Manual - 1 Introduction Thank you for purchasing the Lanzar VIBE Class-D amplifier. Rest assured you have purchased a quality product designed and engineered to give you many years of uncompromised musical service. The VIBE Class-D amplifier has been designed using the latest in electronic technology available today This mono subwoofer amplifier is the result of advanced high speed switching technology that overcomes the less-efficient classAB design. The VIBE Class-D amplifier reflects your true appreciation for powerful bass reproduction in the mobile environment. This amplifier is designed for low-frequency information only andit is not capable of reproducing any mid/high-frequency information. This is due to the noise introduced into the signal by the switching speed of the power supply, which must be filtered out of the audio signal. The power supply incorporated into VIBE amplifier is a DC to DC switching power supply designed to have adequate headroom for even the most demanding peak and dynamic range found on today's Cds and recording. 2 - jCanzar VlBE Owner’s MANUAL __FEATURES ■ CLASS-D DESIGN Low - frequency information for subwoofer only. High efficient power ■ POWER SUPPLIES Stiffly regulated PWM power supplies. MOSFET switches maintain rated power over a wide range of battery voltages. ■ LOW PASS FILTER Adjustable from 50Hz to 150Hz with a slope of 24dB per octave. This allows for the adjustment of the upper point of the frequency bandwidth and the respective subwoofer. ■ VARIABLE SUBSONIC FILTER Adjustable from 15Hz to 40Hz with a slope of 24dB per octave. This allows for the attenuation of frequencies that are mostly inaudible and cause unnecessary strain on the amplifier. ■ PROTECTION CIRCUITRY Protection against thermal, Overload and short circuit conditions. ■ REMOTE DASH-MOUNT GAIN CONTROL This amplifier come complete with a compact remote GAIN CONTROLLER which can be conveniently mounted on or under the dashboard of your car. jCanzar Vibe Owner’s Manual - 3 Specifications MODEL Vlbei800D mono channel amplifier RMS Power, INTO 4 Ohms 400W MONO RMS Power, INTO 2 Ohms 8OOWMONO RMS Power, INTO 1.3 Ohms 1000W MONO MAX Power, INTO 1.3 Ohms 1800W MONO BRIDGE MAX Power, INTO 2 Ohms 3600W MONO THD at 1 Watt, 4 Ohm 0.1% Signal-to-Noise Ratio, below rated power output 90dB Frequency Response, at 1 Watt, 4 Ohm 15Hz co 150Hz (+/-3dB) Damping Factor at 20Hz, 4 Ohm 400 Low Pass Filter 50Hz~150Hz, 24dB/0ctave Variable Subsonic Filter 15Hz~40Hz, 24dB/Octave Bass Boost 0 + 18dB Phase Control 0°to 180 ° Input Sensitivity 200mV to 8V Input Impedance lOKOhm Line Output Impedance lOOOhra Dimensions(Inches) 10.20" x 2.36" x 15.10" Fuse Rating 30A x4 Amplifier Installation 1. Find a suitable location in the vehicle to mount the amplifier. 2. Make sure there is sufficient air flow around the intended mounting location. 3. Bolt the amplifier to the mounting surface. 4. Connect the power ground terminal to the nearest point on the chassis of the car. Keep this ground wire less than one meter (39") in length. Use 4 gauge wire. 5. Connect the remote terminal to the remote output of the head unit using 14 gauge 6. Connect an empty fuse holder within 300mm (12") of the battery and 4 gauge or larger high quality cable from this fuse to the amplifier location. 7. Make sure there is no fuse in this fuse holder. Then make the connection to the "E ATT'' connection on the amplifier. 8. If multiple amplifiers are being used, use cables (each with its own fuse at the battery) or a #0 or a #2 cable from the fuse holder at the battery to a distribution block at or near the amplifier's location. 9. Connect all line inputs and outputs using high-quality RCA-RCA cables. 10. Insert fuse(s) at the battery fuse holder(s). 11. Recheck all connections before powering up. 12. Set all level controls to their least sensitive positions and set all crossover controls, switches, etc. to the desired frequency or position. 13. Once the system is powered up, set the volume control on the head unit to about the 2 o'clock position, and then set all the amplifiers' level controls for maximum output level. 14. Further fine tuning of the various controls may be necessary to obtain the desired results. oCanzar Vibe Owner’s Manual - 5 Features and Controls 6 - jCanzar Vibe Owner’s Manual _ Features and Controls 1. Line Out RCA Jacks - The LINE OUT allows you to build multiple amplifier systems with out having to use splitter cords to distribute the signal. Now it is simple a matter of bringing one set of RCAsinto the first amplifier, then using the line out RCA jacks as the feed to the next amplifier. 2. Line Input RCA Jacks - These inputs are for signal cables from the source. Always use high quality shielded RCA cables. 3. Input Level Controls- Enables the matchi...