Votos - 2, Puntuación media: 4.5
(
)
)
|
Resumen del manual
Tighten the screws securely. When making electrical connections to your amplifier, please observe the following: Use at least 8 gauge wire for power and ground connections. Wire ttie amplifier directly to the car battery. For the ground connection, use the shortest possible wire to a good chassis ground point. Wire the Remote connection to the auto start lead of your head unit, equalizer or power antenna. About power fuses: Lanzar Vector Series amplifiers feature built-in fuse systems. These fuses protect both the amplifier and the electrical system in your vehicle from fault conditions. If you ever need to replace the fuse in your Lanzar Vector Series amp, use a fuse of exactly the same type and rating. A different type or rating ol fuse may result in damage or fire. VECTOR Owner's Manual - 24 troubleshooting protection circuitry The built-in protection circuitry in the Lanzar Vector Series amplifiers will disable the amplifier it it senses an input overload, a speaker short circuit, or extreme temperature conditions. When the protection circuit is activated by any of these conditions, the Protection LED will be Illuminated. It this occurs, carefully inspect the system to determine the source of the problem. • If the shutdown was a result of a thermal overload condition, allow the amplifier to cool down before attempting to restart it. • If the shutdown was a result of an input overload, or speaker short circuit, be sure to correct the condition before restarting. The amplifier can be restarted by turning the remote power OFF and then ON again. No output. Confirm (hat all terminal strip connections are secure and light. Check both In-line and built-in fuses. Both the +12V and the Remote terminals must have+12v referenced to chassis ground Confirm that the audio signal source (car radio, equalizer, etc.) is connected and Is supplying output signal. To check If the amp Is supplying signal, unplug the cables Irom the signal source (but leave them plugged into the amp). Briefly tap the center pm of each of the disconnected RCA plugs with your finger. This should produce a noise (feedback) in your speakers. Only one channel works. Confirm that all terminal strip connections are secure and tight. Check Ihe Balance control on the head unit (or other source) to verity that it is set to its midpoint If you are using the Low Level RCA input, reverse the input plugs at the amplifier (I.e., switch the L with the R). If Ihe channels wnich is silent switches to the other side, the problem is either in the head unit/other source or the connecting cables. Wnk output. Readjust the Input Level Control(s) to better suit the input signal. Nolu In tho audio. If the noise is a "whine" whose pitch follows the engine speed, confirm that the amplifier and any other 3ignal sources (head unit, etc.) are properly grounded. If the noise is a 'clicking' or 'popping' noise whose rate follows the engine speed, this usually means that ihe vehicle Is equipped with resistor spark plugs and wires, or that the ignition is in need of service. Check the rounting of the speaker and input wires to make sure they are not adjacent to wires which Interconnect lights and other accessories. If the above steps fall to Improve or clear noise Interference, the system should be checked by a professional mobile audio installer. VECTOR 0wNit-i Manual - précautions Do not operate the amplifier when it is unmounted. Attach all audio system components securely within the automobile to prevent damage, especially in an accident Do not mount this amplifier so that the wire connections are unprotected, or in a pinched condition, or likely to be damaged by nearby objects. Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals. If you need to replace the power fuse, do so only with a fuse identical to that supplied with the amplifier. Using a fuse of a different type or rating may result in damage that isn't covered in the manufacturer’s warranty. nùmw VECTOR OwNiH'i Manual • 26 notes 9® YES! NT© Two 4-ofun toAAwrs. wired in nerao. will piMant a 4-ohm bad to Mdi cftwntf of Urw amplifier Moat two ohannal wnpllfler* wtll work wall In tit* confirmation. UMMtlAaynntr lOr»r»"«fl >■ an<0M Mm«) NO! Two 4-ohm speaker*. wlrwd In parallel la a bridged two-channel amplifier will preeant a 2-ohm mono toad to the empliRer MOVT TWOCHAMNtt. AMf*UF!lftS DO NOT tUTPONT 1OMN COULD RESULT! YES! ii=@ Four 4-otvn aowatora. wtrwd In eterao, Will p»oaont a 4-otan load to oach cMnftai or tha amp Mar Moat four- Fo<* 4-ohi» »I'M»»». w«rwd In paraM to a brWgad faur-chennet ampler, art! nraaant a 4 ohm none lead to tha №(«« KMT rOUR-CKAMMEL AMFunDO DO NOT WffC...
Otros modelos de este manual:Avtousiliteli - VECTOR VCT-2610 (1.15 mb)
Avtousiliteli - VECTOR VCT-3000D (1.15 mb)
Avtousiliteli - VECTOR VCT-4110 (1.15 mb)
Avtousiliteli - VECTOR VCT-1500D (1.15 mb)