Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
The frequencies below the crossover point will be attenuated at 12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency between 80Hz to 1.2kHz & 50Hz to 500Hz as the crossover point. 2.Set to the "L.P.F" position when the amplifier is used to drive a subwoofer. The frequencies above the crossover point will be attenuated at 12dB /octave. Permits adjustment of the crossover frequency, by rotating the knob to select any frequency between 50Hz to 250Hz & 50HZ to 500Hz as the crossover point. 3.Set to the "OFF" position when the amplifier will be used for driving full-range speakers. The full frequency band width (20Hz - 20kHz) will be output to the speakers without high or low frequency attenuation. 4.Level adjustment-The sensitivity adjustment is to allow the amplifier to work with many different brands of head units. It allows input signal to vary between 350 millivolts to 5 volt from the head unit or other signal processor. Start by setting the sensitivity adjustment to the "MIN" (3 volts).Using a cassette or compact disc that you are familiar with ,turn on head unit to the 3/4 volume setting. Slowly turn up sensitivity adjustment towards the "MAX" (200 millivolts) using a flat head screw driver. Stop turning on the onset of distortion and turn back just a slight. The 3/4 volume setting is now the "maximum" volume for the head unit. The goal is to keep the level control to the lowest setting yet still have enough signal to drive the amplifier. This is done to prevent over driving the amplifier and to keep system noise to a minimum. It is important not over drive speakers (at point of distortion) this will cause permanent damage to the speakers. Also, if the amplifier itself is over driven, it could be damaged. 5.The "BASS" function can be selected to increase low frequency response output, or decrease frequency response output. The "BASS" function will be working at only "OFF" or "L.P.F" position. • The BASS is adjustable from 0 ~ 12dB boost at 50Hz. 11 FRONT/REAR PANEL 12 2CHANNEL ON PROTECT POWER GND REM B+ FUSE CH1 CH2 BRIDGED SPEAKER 30A TUNN T-270 By LINE IN LINE OUT L.P.F L.P.F H.P.F 6V 0.2V 0dB 12dB 50Hz 250Hz H.P.F FLAT 80Hz 1.2KHz CROSSOVER CH1 CH2 CH1 CH2 GAIN BASS ON PROTECT POWER GND REM B+ FUSE CH1 CH2 BRIDGED SPEAKER 25A 25A TUNN T-2100 By LINE IN REMOCON LINE OUT L.P.F L.P.F H.P.F 6V 0.2V 0dB 12dB 50Hz 250Hz H.P.F FLAT 80Hz 1.2KHz CROSSOVER CH1 CH2 CH1 CH2 GAIN BASS ON PROTECT POWER GND REM B+ FUSE CH1 CH2 BRIDGED SPEAKER 30A 30A TUNN T-2130 By T-270,T-2100 T-270 T-2100 T-2130 T-2130 FRONT/REAR PANEL 13 4CHANNEL MONO CHANNEL LINE IN LINE IN GAIN BASS BASS GAIN CROSSOVER CROSSOVER 6V 0.2V 0dB 12dB 50Hz 500Hz CH1 CH2 CH3 CH4 50Hz 500Hz 0dB 12dB 6V 0.2V CH 1/2 CH 3/4 FLAT L.P.F H.P.F FLAT H.P.F L.P.F BRIDGED SPEAKER CH1 CH3 CH2 CH4 ON PROTECT POWER GND REM B+ FUSE 30A TUNN T-460 By 25A SPEAKER BRIDGED CH1 CH3 CH2 CH4 ON PROTECT POWER GND REM B+ FUSE 25A TUNN T-480 By ON PROTECT POWER GND REM B+ FUSE 30A 30A SPEAKER TUNN T-1000M By LINE IN REMOCON LINE OUT GAIN PHASE BASS L.P.F 6V 0.2V 0dB 12dB 50Hz 250Hz CH1 CH2 CH1 CH2 0 180 O O T-460, T-480 T-460 T-480 T-1000M T-1000M TROUBLE SHOOTING GUIDE. This section provides you with a catalog of amplifier symptoms and their probable causes and solutions. Before you consult this listing, make sure the vehicle's electrical system is working properly by verifying that other electrical items (e. g. headlights, windows, etc.) Still function correctly. SYMPTOM PROBABLE CAUSE SOLUTION No Audio Low or N.C Remote Turn-on connectio...
Otros modelos de este manual:Avtousiliteli - TUNN T-1000M (956.17 kb)
Avtousiliteli - TUNN T-2100 (956.17 kb)
Avtousiliteli - TUNN T-2130 (956.17 kb)
Avtousiliteli - TUNN T-270 (956.17 kb)