Votos - 4, Puntuación media: 3.3 ( )

Fabricar: Hifionics Tamaño del archivo: 3.69 mb Nombre del archivo: Idioma del manual:

LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain multiple amplifiers from one signal. The Phase Shift is fully adjustable from 0 to 180 degrees and this allows you to control time alignment. Accepts line level balanced input from 0.4v to 18v. -The LINE INPUT signal is routed directly to the LINE OUT RCA jacks, and not affected by the settings on the amplifier simplifying daisy chaining of amplifiers. The BRE2500.1D is a linkable amplifier and features a MASTER / SLAVE selection switch and IN / OUT RCA connection. The mono amps are capable of 4, 2 & 1-Ohm loads. Operating the amp below 1-Ohm can cause damage to the amp not covered in the warranty. The mono amps are capable of 4, 2 & 1-Ohm loads. Operating the amp below 1-Ohm can cause damage to the amp not covered in the warranty. GLX1000.1D / GLX1400.1D / GLX1800.1D MONO BLOCK AMPLIFIERS GLX2200.1D MONO BLOCK AMPLIFIERS The 4 channel amps have the same features as the 2 channel models accept that there are 2 sets of controls. 1 set for channels 1 & 2 and 1 set for channels 3 & 4. In addition, the 4 channel models have a Mode switch which allows you to select 2 or 4 channel operation. Switch to 2 channel if you only have 1 set of RCA’s in CH 1/2 and the unit will automatically supply signal to channels 3/4. Select 4 channel if you are providing RCA’s to channels 1/2 and 3/4. The X-OVER slide switch selects the internal crossover functions: -The input signal is routed directly to the LINE OUT RCA jacks, regardless of the X-OVER setting simplifying daisy chaining of amplifiers. -HI: Selects the built in HI PASS filter. -FULL: Bypasses all crossovers for full frequency range operation. -LP/BP: Selects the built in LOW PASS filter. LINE INPUT: The line input accepts unbalanced (RCA) inputs from 0.2V to 6V. LINE OUTPUT: The line output passes through signal from the line inputs which allows you to daisy chain multiple amplifiers from one signal. HI PASS: Variable low frequency cut off from 10Hz to 15kHz. LOW PASS: Variable high frequency cut off from 30Hz to 150Hz. BASS EQ: 45Hz bass boost variable from 0dB to 10dB. LEVEL: Variable LEVEL (GAIN) control from 6.0V to 0.2V. Note that the LOW PASS signal is MONO. -In the LP/BP position, the HI PASS filter acts as a subsonic filter. -When the LP/BP mode is selected, a 0 to +10dB, at 45Hz, BASS EQ is also switched in. GLX60.4 / GLX100.4 4-CHANNEL AMPLIFIERS CH1/2 CH3/4 REMOTE HI PASS CH1/2 X-OVER LOW PASS BASS EQ LEVEL POWER LINE OUTPUT 10Hz 15kHz 30Hz 150Hz 0dB 10dB 6.0V 0.2V 10Hz 15kHz 30Hz 150Hz 0dB 10dB 6.0V 0.2V LINE INPUT MODE HI PASS CH3/4 X-OVER LOW PASS BASS EQ LEVEL PROTECT L R L R 2CH 4CH HI FULL LP/BP HI FULL LP/BP INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC LOW PASS L L R R SUB POWER PROTECT BALANCED 9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz INPUT OUTPUT INPUT LEVEL PHASE REMOTE BASS EQ SONIC LOW PASS L L R R SUB IN OUT POWER PROTECT OUTPUT MASTER INPUT SLAVE BALANCED 9V 0.2V 0 180 0dB 10dB 15Hz 35Hz 35Hz 250Hz 3 GLX60.4 / GLX100.4 4-CHANNEL AMPLIFIER APPLICATIONS POWEGRN IDN P U TREM BA TT+12V CH 1/2 SPEAKER OUTPUT CH 3/4 RIGHT LEFT RIGHT LEFT - + - + - + - + BRIDGED BRIDGED FUSE LINE INPUT REMOTE PROTECTPOWER LINE OUT HI FULL LP/BP HI FULL LP/BP 6V 0.2V 10Hz-15KHz 30Hz-150Hz 0dB-10dB HI P ASS LOW P ASS BASS EQ LEVEL X-OVER 1 / 2 CH 6V 0.2V 10Hz-15KHz 30Hz-150Hz 0dB-10dB X-OVER 3 / 4 CH HI P ASS LOW P ASS BASS EQ LEVEL MOCDHE2-CH4 L R L R L R CH1/2 CH3/4 POWEGRN IDN P U TREM BA TT+12V CH 1/2 SPEAKER OUTPUT CH 3/4 RIGHT LEFT RIGHT LEFT - + - + - + - + BRIDGED BRIDGED FUSE LINE INPUT REMOTE PROTECTPOWER LINE OUT HI FULL LP/BP HI FULL LP/BP 6V 0.2V 10Hz-15KHz 30Hz-150Hz 0dB-10dB HI P ASS LOW P ASS BASS EQ LEVEL X-OVER 1 / 2 CH 6V 0.2V 10Hz-15KHz 30Hz-150Hz 0dB-10dB X-OVER 3 / 4 CH HI P ASS LOW P ASS BASS EQ LEVEL MOCDHE2-CH4 L R L R L R CH1/2 CH3/4 4 CHANNEL FULL RANGE SYSTEM 2 or 3 CHANNEL SYSTEM Here we show how to use the 4 channel amplifiers as straight forward discrete 4 - HI PASS: N/A channel full range units. - LOW PASS: N/A Interconnect cable checklist: Channels 3/4: - Connect the four inputs of the amplifier to a Radio/CD with quality RCA cables. - HI PASS: N/A - LOW PASS: N/A Switch setting checklist: - 1/2CH X-OVER: FULL Level control checklist: - 3/4CH X-OVER: FULL - Refer to the section “Setting up systems after installation for best performance” Crossover frequency control checklist: Minimum final loudspeaker impedances: Channels 1/2: - 2 ohm per channel. Here we show how to use the 4 channel amplifiers as a 3 channel unit by taking Switch setting checklist: advantage of the mono bridging capability of all Hifonics amplifiers. - 1/2CH X-OVER: FULL - 3/4CH X-OVER: LP/BP The following example shows how to create a 3 channel system by mono bridging channel pair 3 / 4. In order to create a 2 channel system, simply follow Crossover frequency control checklist: the example to also mono bridge channel pair 1 / 2. Channels 1/2: - HI PASS:...

Descargar ahora

Introduzca dos números de la imagen: