Votos - 5, Puntuación media: 4
(
)
)
|
Resumen del manual
LEVEL MIN MAX LOW IN R L PROTECT POWER REMOTE BASS BOOST HI IN R L 80 2.5k H2 0 BASS BOOST LPF FULL LPF HPF CH4 CH3 CH3 LOW IN CH4 HI IN FREQ. HPF 18db 80 2.5k H2 35 400 H2 80 2.5k H2 35 400 H2 0 18db BASS LEVEL HPF LPF BOOST MIN MAX FULL LPF FREQ. LEVEL MIN MAX HPF CH1 LOW IN CH2 CH2 CH1 HI IN PROTECT POWER REMOTE BASS BOOST CH3/4 head unit Y adaptors speaSkpeakeer Conrnecstions Basic Stereo Output Basic 4CH Output 9 2CH AMPS LA680 LA1080 4CH AMPS LA480 LA580 LA780 LA1480 LA1880 LA2080 + L – + R – BRIDGED GND REM FUUSE 12V + – LEFT speaker RIGHT speaker GND REM FUUUSE + CH1 – + CH2 – + CH3 – + CH4 – 12V + BRIDGED – + BRIDGED – FRONT speakers REAR speakers L R R L Speaker Connections 2 CH Mono-Bridged Output Bridged Mono Output LA680 LA1080 4CH AMPS 2CH AMPS LA480 LA580 LA780 LA1480 LA1880 LA2080 + L – + R – BRIDGED GND REM FUUSE 12V + – GND REM FUUUSE + CH1 – + CH2 – + CH3 – + CH4 – 12V + BRIDGED – + BRIDGED – speakers L R MINIMUM SPEAKER IMPEDANCE 4 OHMS! speaker MINIMUM SPEAKER IMPEDANCE 4 OHMS! speakers MINIMUM SPEAKER IMPEDANCE 4 OHMS! GND REM FUSE 12VCH4+ –CH2+ –CH1+ – CH3+ – BRIDGED+ – BRIDGED+ – L R GND REM FUSE 12VCH4+ –CH2+ –CH1+ – CH3+ – BRIDGED+ – BRIDGED+ – L R Mono Subwoofer Amplifier will not power up. • Check for good ground connection. • Check that remote DC terminal has at least +12v DC. • Check that there is battery power on the + terminal. • Check all fuses. • Check that Protection LED is not lit. If it is lit, shut off amplifier briefly and then repower it. High hiss or engine noise (alternator whine) in speakers. • Disconnect all RCA inputs to the amplifier(s) – if hiss/noise disappears, then plug in the component driving the amplifier and unplug its inputs. If hiss/noise disappears, go on until the faulty/noisy component is found. • It is best to set the amplifier's input level as insensitive as possible. The best subjective S/N ratio is obtainable this way. Try to drive as high a signal level from the head unit as possible. Protection LED comes on when the amplifier is powered up. • Check for shorts on speaker leads. • Check that the volume control on the head unit is turned down low. • Remove speaker leads, and reset the amplifier. If the Protection LED still comes on, then the amplifier is faulty. LA680 LA1080 4CH AMPS 2 CH Stereo plus Mono-Bridged Subwoofer Output TROUBLESHOOTING Before removing your amplifier, refer to the list below and follow the suggested procedures. Always test the speakers and their wires first. Amplifier(s) gets very hot. • Check that the minimum speaker impedance for that model is correct. • Check for speaker shorts. • Check that there is good airflow around the amplifier. In some applications, an external cooling fan may be required. Distorted sound • Check that the Level control(s) is set to match the signal level of the head unit. • Check that all crossover frequencies are properly set. • Check for shorts on the speaker leads. High squeal noise from speakers. • This is almost always caused by...
Otros modelos de este manual:Avtousiliteli - Legacy LA2080 (1.12 mb)
Avtousiliteli - LA1080 (1.12 mb)
Avtousiliteli - LA580 (1.12 mb)
Avtousiliteli - Legacy LA1480 (1.12 mb)